Master Print — Manual de Campo

VersaWorks Print Mode: Quality vs Speed and What Passes and Resolution Do to Banding, Drying and Ink

Picking the fastest mode looks like profit, right up until the banner comes out banded and wet. I explain what passes, resolution and carriage direction change on your Roland, how that affects banding, drying and ink use, and how to pick the right mode for each job.

Friday afternoon, four storefront banners due and the printer crawling along. The fix looks obvious: switch to the fastest mode in VersaWorks and go. The first banner comes off in half the time, but with visible bands across the solid background, thinner color and ink still sticking on the take-up roll. You saved an hour and lost the print.

This dilemma lands on my bench every week. "What's the best VersaWorks print mode?" doesn't have one answer, because every mode is a trade-off between speed, banding, drying and ink. Here I explain what passes, resolution and carriage direction really do on machines like the SP-540V, VP-540i, VS-640i, RS-640, RE-640, RF-640 and RA-640, and how to choose without guessing. Exact mode names vary by model and RIP version; the full calibration is in the course.

Sound familiar?

  • Fast mode shows bands; quality mode doesn't.
  • Prints come out wet whenever you speed up.
  • High quality mode takes so long it blows the deadline.
  • Color shifts between modes with the same file.
  • You never know which mode to use for banner, vinyl or close-up decals.

What a "pass" is and why it controls everything

The head doesn't print the image in one go. It covers each strip of media in several passes, with the media advancing a little between them. More passes means a smaller advance per carriage stroke and the same area receiving ink in smaller doses, more times.

That has three direct effects. First, more passes spread errors out: a weak nozzle or a feed that's slightly off gets diluted across several passes instead of drawing a line. Second, ink arrives in thinner layers, which gives the heaters time to work. Third, everything gets slower. Fewer passes do the opposite: faster, but every small defect shows.


Resolution: more dpi isn't always more quality

The classic owner mistake is assuming higher resolution is always better. For a storefront banner seen from fifteen feet away, a lower resolution with a sensible number of passes often delivers more than the printer's finest mode. For close-up decals, photos with skin tones or small text, higher resolution makes a real difference.

Resolution and passes travel together inside each mode, and every combination has its own ink behavior. That's why the same file can print with different color in two modes: the profile and ink laydown may change along with it. If your color moved after switching modes, that's expected, not a defect.


Fast mode and banding: the direct link

Horizontal banding that appears only in fast mode is one of the clearest signals you'll ever get. It usually points to one of two things: media feed isn't tuned well for that media, or there's a weak nozzle the extra passes were hiding. In fast mode, the defect is exposed.

  • Regular bands in every color: think feed and media settings first.
  • Bands in one color or at a fixed position: think nozzles and the nozzle check.
  • Bands only with bidirectional printing: there may be a mismatch between the carriage's left and right strokes.

I break that down in Roland printer banding. The point here: if only fast mode bands, the printer is showing you an adjustment that needs doing, not necessarily a serious fault.


Drying: the side nobody does the math on

In fast mode the same amount of ink has to dry in far less time. The media moves past the heaters faster and reaches the take-up still damp. The result: ink transferring to the back, marks in the roll, color that shifts once it dries and, sometimes, bleeding in solid areas.

In a slower mode the ink goes down in thin layers and spends more time under heat. That's why media that floods in fast mode can come out perfect just by changing modes. If your ink won't dry even in slow mode, that's a different problem, which I cover in Roland ink not drying.

A banded or wet print is a reprint, and a reprint eats exactly the time you were trying to save.

Knowing which mode to use on each media and tuning feed and drying so fast mode also comes out clean is exactly what I show on video in Manual de Campo, on a real machine. Show me how to print fast without losing quality →


Bidirectional or unidirectional: the hidden choice

Besides passes, many modes let you choose whether the head prints on both carriage strokes or in one direction only. Printing both ways is much faster, but it needs the left and right strokes to line up well; any mismatch shows up as doubled outlines, "fuzzy" text or fine bands in solid areas. Printing one way only removes that mismatch, at the cost of time.

When a printer comes in with complaints of a "shaky image" only in fast mode, that's the first thing I look at. Often the mode is fine and what needs attention is the alignment, which varies with the model and the head height being used.


Ink use: what actually changes

Lots of people assume slow mode burns far more ink. In practice, the main driver of ink use is the profile and the ink limit tied to each mode, not just the number of passes. Some quality modes lay down more density, others don't. What usually happens is the opposite of what the owner expects: a poorly tuned fast mode wastes more, because it causes reprints.

And repeated cleanings to "fix" banding that was really a mode or feed issue burn more ink than any print mode ever will.


A typical case from the bench

A shop printed everything in the printer's finest mode "just to be safe." Production crawled, and even so the banner came out soaked on cold days. Once we set criteria by job type, banners moved to a middle mode, drying was sorted out and close-up decals stayed in the fine mode. The printer didn't change; the choice did.


How far to go on your own, and where Manual de Campo comes in

With what's here you can already make a smarter choice: faster modes for prints seen from a distance, more passes for photos and close reading, and attention to drying whenever you speed up. Safe things to check:

  • print the same file in two modes and compare banding, color and drying;
  • run a nozzle check before blaming the mode;
  • see whether the banding disappears with more passes;
  • write down which mode works on each media in your shop.

What takes a method is getting fast mode clean: tuning feed per media, aligning the carriage's two directions, balancing the heaters and knowing when the defect is the machine. I show that on video, on a real machine, in Manual de Campo, along with the media setup in VersaWorks media settings.

If you're always choosing between deadline and quality, you're leaving money on the table. Join Manual de Campo today and learn to set up your Roland to print fast when you can and print fine when you must.


Quick questions about VersaWorks print modes

Frequently Asked Questions

1. What is the best print mode in VersaWorks?

There isn’t a single best one. Prints viewed from a distance handle faster modes; photos, small text and close-up decals need more passes or resolution. Mode names vary by model and RIP version.

2. Why does only fast mode show banding?

With fewer passes, any feed error or weak nozzle becomes visible. More passes spread those small defects out. Banding only in fast mode usually means an adjustment is needed, not a major fault.

3. Does high quality mode use more ink?

Not always. Ink use depends mostly on the profile and ink limit tied to each mode. What wastes the most ink and media is reprinting jobs that came out banded or wet.

4. Why do prints come out wet in fast mode?

The media passes the heaters faster and takes ink in heavier layers, so it reaches the take-up damp. Switching to a mode with more passes or revisiting drying usually solves it.

5. Does Manual de Campo teach choosing and tuning modes?

Yes. In the course I show on video, on a real machine, how to pick the mode for each job and how to tune feed and drying so you can print fast without banding.

  • 🎥 Print modes explained on video, on a real machine
  • ⚖️ Quality and speed balanced for every job
  • ⚡ Instant access as soon as payment is confirmed
  • ♾️ Lifetime access to Manual de Campo and future updates
Pick the Right Mode on My Roland