Roland Printer Banding: Horizontal Lines from Nozzles, Feed, Media or Print Mode?
Horizontal stripes running across your prints? I explain how to identify the cause of banding on your Roland just by reading the band pattern, and the right order of checks.
The solid blue background on that banner came out striped from edge to edge. You reprint, switch the mode, run a cleaning "just in case"… and the lines come back. Sometimes in the same spot, sometimes lighter, sometimes only on one side. Wasted media, wasted ink, and a customer asking if the job is ready.
Banding is one of the most common complaints that land on my bench, and the classic owner mistake is changing everything at once: clean the head, recalibrate feed and swap profiles on the same day. Here I'll show you how to read the banding pattern to know where it comes from, and which part of the diagnosis has to be seen on the machine.
Does this look like your print?
- thin lines repeating at even intervals;
- a light or dark band running across every color;
- banding only in magenta (or only in one color);
- lines that show up in one section of the job and disappear in another;
- perfect in quality mode, striped in fast mode.
What banding is and why it happens
On a Roland eco-solvent printer (VP-540, SP-540V, RS-640, VS-640, RE-640), the image is built in passes. The carriage moves across, prints a band, the media advances a little, the carriage passes again, and so on. When anything in that sequence is off, the seam between passes becomes visible. That's banding.
There are two main "types" of band:
- light/white bands: missing ink in that area (nozzles dropping out, or the media advancing too far and leaving a gap);
- dark bands: too much ink (the media advancing too little, so passes overlap).
That difference alone helps a lot: light bands and dark bands point your diagnosis in different directions.
The four big causes of banding on Roland printers
1. Missing or deflected nozzles
If a group of nozzles doesn't fire or fires at an angle, every pass carries a "hole" in the same position. The result is fine lines repeating at regular intervals, usually leaning toward one specific color. It's the most common cause and the first one to rule out.
2. Feed calibration off
If the printer advances the media slightly more or less than it should, the passes don't fit together. You get light or dark bands in every color at once, evenly spaced. This setting changes from one media to another, which is why the problem seems to show up "out of nowhere" when you switch material.
3. Media and tension
Wavy media, a heavy roll that drags, a badly seated core or uneven tension make the feed vary during the job. Then the banding is not consistent: worse in one section, gone in another, sometimes only on one side of the print.
4. Print mode and profile
Fast modes with fewer passes make seams more visible. A media profile laying down too much ink can also mark the passes. Sometimes the printer is fine and the banding comes from the settings chosen in the RIP.
What I see most in practice: banding the owner swore was "the head" that turned out to be media feed, right after a roll change. The opposite happens just as often: someone recalibrates feed three times to make up for a deflected nozzle. When a print like that comes in, the first thing I check is whether the band is in one color or all of them.
How to tell the causes apart by looking at the print
- Banding in one color only (e.g. only magenta): almost always nozzles. Go straight to the nozzle check.
- Banding in all colors, evenly spaced: strong suspicion of feed calibration.
- Irregular banding that changes during the job: media, tension, roll or environment.
- Banding only in fast mode that disappears in quality mode: a print mode limitation.
- Banding on one side of the media only: skewed loading, pinch roller position or uneven tension.
Practical tip: print a solid block of each ink channel plus a block of composite black. Comparing those blocks side by side tells you far more than staring at a full-color photo.
A typical case: new banner roll, first job of the day, regular dark bands in the solid background. Nozzle check perfect. The culprit wasn't the head at all: feed had been calibrated for a different media. If that sounds like you, read the Roland feed calibration guide.
A banded print is a reprinted print: media, ink and deadline thrown away.
This is exactly the diagnosis I show on video, on a real machine: look at the band, know whether it is nozzles, feed, tension or print mode, and apply the right protocol to get rid of banding. Stop the banding now →
A logical order of checks (without messing up the printer)
The most common mistake is adjusting calibration when the problem was nozzles, or cleaning the head when the problem was feed. Here's the order I use:
Banding checklist
- 1. TEST PRINT: is the nozzle pattern complete? If there are gaps, fix that first. Never calibrate feed with missing nozzles.
- 2. Media: is it loaded straight, with the pinch rollers in the right positions and no waves?
- 3. Roll and core: does the media turn freely, without dragging or pulling too hard?
- 4. Feed calibration: if the nozzle check is perfect and the banding shows in every color, run the feed calibration (FEED/MEDIA CALIBRATION, depending on the model) for that media.
- 5. Print mode: print the same file in a mode with more passes in VersaWorks. If it disappears, you've found the limit of the fast mode.
- 6. Profile: make sure the media profile matches the material that's loaded.
Any time you need to physically inspect the media path, rollers or carriage, power the printer off and unplug it. Loading media follows the normal panel procedure; mechanical inspection is done with the machine de-energized.
Common mistakes that bring banding back
- calibrating feed on one media and printing on a completely different one;
- adjusting feed with missing nozzles, "compensating" one problem with another;
- letting the printed output pile up on the floor and pull on the media;
- using a very fast production mode for window graphics or photo work;
- ignoring humidity and temperature, which change how media behaves.
Banding: what you can fix yourself and when it becomes a shop diagnosis
With this order of checks, most Roland printer banding gets solved with a nozzle check, correct loading and feed calibration. When it still won't go away, a more technical stage begins:
- evaluating the feed system (grit rollers, pinch rollers, wear);
- confirming whether the problem is mechanical or settings-related with controlled tests;
- telling deflected nozzles apart from a head alignment issue;
- building profiles and print modes that balance quality and speed.
From here on, you need to see the machine: the diagnosis depends on seeing the print, the test and the machine together. That's why the complete banding protocol is in video lessons inside the Field Manual, with real examples of each type of band and what to do in each case.
If the banding is still there after the basics, every blind reprint is media and deadline going out the door. In the Field Manual I show on video, with real prints, how to identify each type of band and what to do in each case, in the right order, until the job comes out clean. Get in now and stop reprinting just to find the cause.
What you gain by understanding banding
- you stop guessing calibration and cleaning at the same time;
- you identify the cause just by reading the band pattern;
- you waste less media and ink on reprints;
- you deliver clean, stripe-free graphics and hit deadlines with confidence.
That's what the Field Manual for Roland Printers is about: a method, not trial and error.
FAQ: banding and horizontal lines on Roland printers
Frequently Asked Questions
1. How do I know if banding is a nozzle problem or a feed problem?
Look at the color of the band. If it shows up in one color only, it's very likely nozzles; confirm with the TEST PRINT. If it shows in every color, evenly spaced, and the nozzle check is complete, the main suspect becomes the feed calibration for that media.
2. Do I need to recalibrate feed every time I change media?
Ideally you keep a proper calibration for each media type you use regularly. Materials with different thickness, surface and liner advance differently. If you switch media a lot and never recalibrate, banding showing up is expected.
3. Why does banding disappear in quality mode?
Modes with more passes overlap the image more and hide small variations in feed and nozzles. If banding only appears in fast mode, the printer may be fine and you're hitting the limit of the mode. Still, check the nozzle test and the calibration.
4. What does banding on only one side of the print mean?
It usually points to skewed media loading, uneven roll tension or pinch rollers in the wrong position. Reload the media carefully, check the roll and test again before moving on to adjustments.
5. When is banding a sign of a mechanical problem?
When the nozzles are complete, calibration was done correctly, the media is loaded well and the bands still persist or vary with no pattern. That's when the feed system needs evaluating, which I walk through step by step on video in the Field Manual.
- 🎥 Straight-to-the-point video lessons on a real machine
- 🛠️ Focused on VP, SP, RS, VS, RE and RF with real cases
- ⚡ Immediate access to content after confirmation
- ♾️ Lifetime access to the Field Manual and future updates