Roland ink not drying: heater settings, TEMPERATURE IS TOO LOW and media setup
Smudged prints, running ink and TEMPERATURE IS TOO LOW almost always involve heaters, environment and media. Here I explain the causes and the safe checks on your Roland.
You run a finger over the print that just came out and the ink smears. The solid black is pooling, the vinyl sticks to its own back on the take-up roll, and sometimes the panel throws TEMPERATURE IS TOO LOW right when you need to start the job.
Poor drying is one of the most common complaints I hear in the shop, and the classic owner mistake is cranking the heat up by guesswork until the media cockles. It almost always comes down to three things: heaters, the room and the media settings. Here I'll explain how drying works on a Roland eco-solvent printer, what that warning points to and what you can check without risk.
Sound familiar?
- ink smearing when you touch it at the output;
- dark solid areas pooling or running;
- vinyl sticking or transferring ink on the roll;
- TEMPERATURE IS TOO LOW showing up often;
- laminate lifting or bubbling days later.
How heating works on a Roland eco-solvent printer
On machines like the SP-300/540V, VP-540/540i, RS-640, VS-640/640i, RE-640 and RF-640, drying is not just a matter of time. It happens in stages:
- Print heater: heats the platen right in the print zone. It helps ink settle on the media and starts evaporating solvent the moment the drop lands.
- Dryer: a heater just after the print zone that continues drying as the media advances.
- External dryers: in heavier production, many shops add an extra dryer (airflow or heat) at the output.
Eco-solvent ink dries by solvent evaporation. Heat, airflow and time speed it up. Cold, high humidity and too much ink slow it down.
The way I explain it at the counter: if heat + air + time cannot keep up with the amount of ink you are laying down, it will not dry.
What "TEMPERATURE IS TOO LOW" means
This message is a temperature-related warning: depending on the model, it means the room temperature and/or the heaters are still below what's needed to print properly. There is no single cause, so the first step is to notice when it shows up.
It usually shows up when:
- you send the job right after powering on or right after the printer wakes from sleep;
- the room is cold and the heaters take longer to reach temperature;
- there is a draft (AC vent, window, fan) blowing over the platen;
- the set temperature is too high for that environment;
- less commonly, there is a fault in a heater or in temperature control.
If the message clears after a few minutes and printing goes on normally, it was just warm-up. If it keeps coming back in a normal room, it is worth digging deeper.
Why ink will not dry: the most common causes
- Heater temperature too low for that media and ink load.
- Too much ink: a color profile or ink limit that does not suit the media, especially in dark solid colors.
- Print mode too fast, with no drying time between passes.
- Cold or humid room, outside the range in your model's manual.
- Wrong media, without a coating made for eco-solvent ink.
- Rolling up too soon: the take-up winds the media while still wet and ink transfers to the back.
- No airflow at the output: solvent evaporates but just hangs over the media.
And when the problem is too much heat?
- Media cockling or wrinkling on the platen, which can even rub against the head.
- Nozzles drying out more easily because of heat near the head.
- Media shrinkage, affecting registration and contour cutting on print&cut jobs.
What I see most in practice: a profile laying down too much ink for the media, a fast mode and the take-up winding right at the output. Any one of those hurts; all three together and no heater can keep up. When a drying complaint comes in, the first thing I check is the profile's ink load, before the temperature.
Symptoms of poor drying
- Ink running or pooling in solid color areas.
- Smudging when you touch the print right at the output.
- Roller or platen marks on the print.
- Banding that gets worse in solids and better in slower modes.
- Ink transfer to the back of the media on the roll.
- Lamination and adhesion problems later, because solvent has not fully gassed out.
A typical case: winter, a cold room, AC blowing straight onto the platen. The owner pushed the heaters to the max, the media started cockling and nearly touched the head. The real problem was the room. If poor drying comes with stripes in solid areas, also check the Roland banding guide.
Every meter that comes out smeared is media, ink and machine time thrown away.
This is exactly the diagnosis I show on video, on a real machine: separating the room, the heaters, the profile and the print mode, and the method to get ink truly dry on every media. Fix my drying problem →
Safe basic checks
Heads up: the platen and heaters get hot. Do not touch the heated area, and for any physical inspection switch off at the panel, turn off the main power switch, unplug and let it cool down. Never open covers to "look at the heater".
1. Environment
- Check room temperature and humidity against the range in your printer's manual.
- Remove direct drafts over the platen (AC vents, fans, open doors).
- Give the printer time to warm up before sending the job.
2. Settings
- Make sure the heaters are on and set to a temperature suited to that media.
- Check that the media profile in VersaWorks matches the material loaded.
- Try a slower print mode or more passes and compare.
3. Media and output
- Confirm the media is made for eco-solvent ink.
- Leave length or time before the take-up winds it.
- Consider airflow at the output for heavy ink loads.
Change one thing at a time and print the same test strip. That is how you find out what actually fixed it.
Quick drying checklist
- Room within the manual's range, no drafts over the platen.
- Heaters on and up to temperature before printing.
- Correct media profile in VersaWorks.
- Print mode matched to the ink load.
- Media made for eco-solvent ink.
- Time and airflow before rolling up and before laminating.
Drying: what is an operator adjustment and what needs a method
Environment, warm-up time, media profile and print mode are operator adjustments. What I do not recommend doing from reading alone:
- building print heater and dryer temperature combinations for each media without a method;
- adjusting ink limits and profiles in VersaWorks without understanding the impact on color;
- diagnosing whether a constant TEMPERATURE IS TOO LOW is the room, the settings or a heater fault;
- fixing media cockling that rubs against the head.
Getting this wrong costs media, reprints and, in the worst case, a head striking cockled media. That is why the complete per-media drying setup method is in the video lessons inside Manual de Campo, on a real Roland, with the tests and the right order of adjustments.
If your ink isn't drying and the customer is waiting, every smeared meter is media, ink and machine time in the trash. In Manual de Campo I show on video, on a real Roland, how to dial in heaters, print mode and profile for each media, without cooking the head or cockling the material. Get in now and stop adjusting by guesswork.
What you gain by getting drying right
- Fewer reprints and less wasted media.
- Lamination and installs without bubbles or lifting.
- More consistent color from job to job.
- A protected head, safe from excess heat and cockled media.
Quick questions about Roland heaters and drying
Frequently Asked Questions
1. What should I do when my Roland shows TEMPERATURE IS TOO LOW?
Start with the context: right after power-up or coming out of standby, the printer often just hasn't reached the required temperature yet. If the warning shows up often, check the room temperature against the range in your model's manual, drafts over the platen and the heater settings. If it persists with a normal room and normal settings, it needs a deeper diagnosis.
2. Can I just crank the heaters to maximum so the ink dries?
Not a good idea. Too much heat cockles and shrinks media, can make it rub the head and helps nozzles dry out. The right approach is balancing temperature, print mode, ink load and airflow for each media.
3. Why does ink dry fine on one media but not another?
Every media has a different coating, thickness and absorption. A media without an eco-solvent coating, or a profile laying down too much ink, will fail to dry even with the heaters on. That is why each material needs its own setup.
4. How long should I wait before laminating an eco-solvent print?
The media and ink manufacturers specify the recommended outgassing time. The key point is that ink that is dry to the touch may still be releasing solvent, and laminating too early can cause bubbles and adhesion failure.
5. Is an external dryer worth adding to my Roland?
For heavy ink loads, dark solids or high-speed production, a dryer or airflow at the output helps a lot. It complements the print heater and dryer, but it does not replace a correct media setup.
- 🎥 Per-media drying setup on video, on a real machine
- 🛠️ Print heater, dryer and VersaWorks on SP, VP, RS, VS, RE and RF
- ⚡ Immediate access to content after confirmation
- ♾️ Lifetime access to Manual de Campo and future updates