Roland Not Cutting All the Way Through: Incomplete Cuts and Skipped Lines
Blade scoring the vinyl but not cutting through, or skipping parts of the contour? From the service bench, I explain why cuts come out incomplete on Roland VP, VS and SP print-and-cut machines, what to check safely and why cranking up the force is rarely the answer.
The sheet comes off the machine, you go to weed the first sticker and it won't lift. The blade scored the vinyl but never made it through. One corner is perfect, the other is barely marked, and on a few letters it looks like the machine just skipped a chunk of the outline. Out comes the hobby knife, the rework starts and the customer is texting to ask if the order is ready.
A Roland not cutting all the way through is one of the complaints I hear most from print-and-cut owners. What I find on the bench is almost always the same story: nothing is broken. It's the mix of blade, blade holder, cutting strip, media and file that drifted out of spec. Here I cover this on the VP-300/540/540i, VS-300/540/640/640i and SP-300/540V, show you what you can check without risk, and tell you plainly what stays in the Manual de Campo video lessons. The RS-640, RE-640, RF-640 and RA-640 are print-only, so none of this applies to them.
Sound familiar?
- The blade marks the vinyl but never reaches the liner.
- It cuts fine on one side of the media and fails on the other.
- Some lines get cut, others look like they were skipped.
- The start of the contour does not meet the end.
- It started after a new blade or a new brand of vinyl.
What a "complete" cut actually needs
For a sticker to weed cleanly, the blade tip has to go through the vinyl and the adhesive and stop at the liner without punching into the backing. That depends on four things working together: how much of the tip is exposed, the force applied, how sharp the edge is and a firm, smooth surface underneath, which is the cutting strip under the cutting carriage.
When any one of those four drifts, the result looks the same: a scored line that won't weed. That's why turning the force up without thinking is the classic mistake. Sometimes it works for a day, sometimes it starts cutting the liner too, and sometimes nothing changes because the problem was somewhere else.
Blade and blade holder: where most cases live
When a VP or VS comes in with cuts failing, the blade holder is the first thing I pull. Here's what I usually find:
- A worn or chipped blade. Under a loupe, the tip is no longer sharp and even. A dull blade doesn't cut, it pushes the vinyl.
- Too little tip exposed. After a blade change, it's common to leave the blade retracted more than the media needs.
- Gunk inside the holder. Bits of vinyl and adhesive build up and stop the blade from swiveling freely, so it starts cutting sideways.
- Inconsistent blade quality. Very cheap blades vary from one to the next, so the same settings give different results.
Force and offset are their own topic, which I covered in the article on Roland cutting blade force and offset. I'm not giving numbers here on purpose: they change with blade type, media and machine condition, and a value copied from a forum is the fastest way to cut through your liner.
The cutting strip nobody looks at
Under the blade path there's a protective cutting strip. Over time it gets scored, grooved or deformed, especially in the zone where you always cut: small stickers, always in the same spot on the media.
Once that strip is worn, the blade loses its firm backing there. The symptom is very recognizable: perfect cuts across one part of the width and failures in another, even with a new blade. A case I see again and again: the owner goes through three blades, raises the force twice, and the cut keeps failing in the same band. Look at the strip and there's a visible groove right there.
Media, ink and speed play a part too
- Different media, different behavior. Thicker, reflective, frosted or laminated vinyl needs different settings. New supplier, new cut test.
- Ink that is still soft. Cutting right after printing, while the ink is still releasing solvent, makes the vinyl gummy and the cut uneven. If drying is already weak, read about Roland ink not drying.
- High speed on detailed artwork. On tight curves and small text, the blade can't keep up and skips sections.
- Media lifting during the cut. If the vinyl ripples or lifts off the platen, the blade loses depth exactly at those spots.
Every sheet that comes out half-cut is media, ink and labor going in the trash.
Sorting out blade, holder, cutting strip, media or file, in the right order and without spinning settings at random, is exactly the diagnosis I walk through on video in Manual de Campo, on a real machine. Show me the cutting diagnosis on video →
When the problem is the file, not the machine
If the machine skips whole sections of the contour, look at the file first. The usual suspects:
- some of the lines aren't in the cut color VersaWorks recognizes, so they never get sent to the cutter;
- open paths that don't close where they start;
- duplicate lines stacked on top of each other;
- details too small for the blade to physically follow.
Building the cut line correctly matters so much that I put those tips in a separate article on setting up a CutContour line for VersaWorks. And when the contour doesn't quite close at its start point, there's an overcut option in the cut settings that helps close it, but it won't make up for a worn blade.
Safe checks before you touch any setting
- run the machine's own cut test on a vinyl scrap and weed it with your fingernail: it tells you whether the problem is general or only in that job;
- pull the blade holder, check the tip with a loupe and clean out vinyl and adhesive;
- with the machine off, check the cutting strip for visible grooves or deformation;
- test with a roll you know cuts well, to separate a media issue from a machine issue;
- compare the start and end of a long job: if it gets worse toward the end, suspect media tracking off its path.
Change one thing at a time and test again. Swapping the blade, force and speed all at once means you never know what actually fixed it.
How far to go on your own, and where Manual de Campo comes in
The checks above are safe and they solve a good share of worn-blade, dirty-holder and bad-file cases. When they don't, the diagnosis moves into:
- setting blade exposure and force for your specific model and media;
- assessing and replacing the cutting strip without knocking anything out of line;
- separating a cutting fault from a media feed problem;
- checking the cutting carriage assembly when the failure comes and goes.
The full step-by-step, with the right order of tests and adjustments, is what I show on video, on a real machine, in Manual de Campo.
If you have already swapped the blade, already raised the force and the cut still fails, stop turning knobs in the dark. Get into Manual de Campo today, follow the cutting diagnosis on video and get back to shipping stickers that weed clean, no hobby knife, no wasted media.
Quick answers about incomplete cuts on a Roland
Frequently Asked Questions
1. Why does my Roland only score the vinyl instead of cutting it?
Most of the time it's a worn blade, too little tip exposed, a dirty blade holder or a grooved cutting strip. Low force can cause it too, but raising force without checking the rest usually creates a new problem: cutting into the liner.
2. Can I just turn up the cutting force?
It can help if force really is too low, but it shouldn't be your first move. Check the blade and cutting strip first. High force on a dull blade tears the vinyl and scores the liner.
3. Why does it cut on one side of the media and fail on the other?
The classic suspect is a cutting strip worn in that zone, or media without firm support at that point. Run cut tests at different positions across the width to confirm.
4. The machine skips parts of the design. Is it broken?
Rarely. Usually some lines aren't in the cut color, or the paths are open or too detailed. Review the file before blaming the machine.
5. When is it worth following Manual de Campo?
When you have already checked the blade, holder, cutting strip, media and file and the cut is still inconsistent. From there the adjustment takes method, and that sequence is what I show on video, on a real machine.
- 🎥 Straight-to-the-point video lessons on a real machine
- 🛠️ Step-by-step cutting diagnosis for VP, VS and SP
- ⚡ Instant access as soon as payment is confirmed
- ♾️ Lifetime access to Manual de Campo and future updates