Roland Print Cut Off at the Edge: Wrong Margins and Print Shifted on the Media
Artwork coming out with one side cut off, a bigger margin on one side or the print shifted on the media? From the workshop, I explain why the image gets cut off at the edge on your Roland and what to check in the file, in VersaWorks and on the machine.
The banner art was 50 inches wide and the roll was wider than that. Still, the print came out with the customer's logo chopped off on one side, a huge margin on the other and half the phone number missing. You check the file: it's fine. You send it again, same result. And there goes another stretch of banner material.
A print cut off at the edge looks like a hardware fault, but on the bench it almost never is. What I see most is a mix of printable area, origin point, media reading and job setup. Here I explain why a Roland print gets cut off at the edge on the SP-300/540V, VP-300/540/540i, RS-640, VS-300/540/640/640i, RE-640, RF-640 and RA-640, what you can check safely and what I keep for the Manual de Campo video lessons.
Sound familiar?
- One side of the art is cut off, even with media to spare.
- The margin is wide on one side and almost zero on the other.
- The start or the end of the print goes missing.
- The print lands further to one side than it should.
- It started after a new media type or moving the pinch rollers.
The machine only prints where it thinks there is media
When you load media and lower the lever, the Roland reads the media and sets the printable area: where it starts, where it ends, how much width is available. Anything outside that area doesn't print; it just gets clipped.
That's why wide media does not guarantee a wide printable area. If the machine read the edge wrong, if the media went in offset, or if the pinch rollers sit where they limit the area, the width the machine "sees" can be narrower than the art. And it clips whatever doesn't fit.
One more detail catches people who are just starting out: the machine always reserves a minimum margin on the sides, which varies with model and settings. Art designed to run edge to edge on the media will lose a strip. The fix isn't in the machine, it's in planning: slightly wider media, bleed built in and finishing after printing.
Origin point and margins: the most common culprit
The classic owner mistake goes like this: on the previous job, someone moved the origin point at the panel to use up a leftover strip of media. On the next job nobody remembered to reset it, so the print starts offset and pushes the art outside the printable area.
- an origin point moved by hand and forgotten;
- side margins set differently from what you think;
- a previous job that left the media advanced or shifted;
- more than one job in the queue, placed side by side.
A simple shop habit: before you release a big job, check the printable width the machine read on the panel and compare it with the width of the art. If it doesn't fit, sending it won't help.
When the problem is the file or VersaWorks
The machine isn't always to blame. The file-side causes I see most:
- Artboard smaller than the art. Part of the design sits outside the document page and gets dropped on export.
- Scaling in VersaWorks. The job was enlarged or rotated in the RIP and ended up wider than the printable area.
- PDF bleed and trim boxes. Exporting with the wrong box clips the art before it ever reaches the Roland.
- Wrong media setup. A width or media type that doesn't match what's loaded. It's worth reviewing your VersaWorks media settings.
Every banner that comes out with a clipped edge is media, ink and a deadline down the drain, and the print head is almost never the reason.
Sorting out file, VersaWorks, media reading or origin point, and checking all of it before you print, is exactly the routine I show on video in Manual de Campo, on a real machine. Show me how to stop clipping my prints →
Reading the media edge: sensor and material type
Your Roland uses a sensor to find the edges of the media. Clear, very glossy, reflective or dark materials can confuse that reading, and the machine sets the printable area in the wrong place. The typical symptom is a print always shifted to the same side with one specific media, and normal with everything else.
A dirty sensor gets in the way too. If the machine actually complains it can't find media, or measures strange widths, see the article on a Roland media sensor not detecting.
Skewed media and the end of the print disappearing
If the clipped edge only shows up at the end of the job and gets worse along the length, the suspect changes: the media is feeding skewed or "walking" to one side as it advances. It starts inside the area and finishes outside it.
- media loaded without lining it up with the machine's reference;
- a roll with a telescoped core or sitting poorly on its holder;
- pinch rollers gripping unevenly;
- a short end of print because the length is out of calibration, which ties into Roland feed calibration.
A case I see again and again: the owner switches banner suppliers, and suddenly long banners come out with the side clipped in the last few feet. It wasn't the machine. The new roll's core sat loose on the holder and let the media drift to one side.
Safe checks before you print again
- make sure the origin point wasn't left changed from a previous job;
- compare the printable width the machine read with the width of the art;
- open the job in VersaWorks and look for any scaling or rotation;
- print a short test, a rectangle the exact size of the art, before the big job;
- reload the media straight and gently clean around the sensor, with the machine off.
How far to go on your own, and where Manual de Campo comes in
In most cases, checking origin, printable area, file and loading solves it. When the image still comes out clipped or shifted with all of that right, the diagnosis moves into:
- testing to separate file, RIP, sensor reading or media feed;
- adjusting loading and pinch rollers for each media type;
- checking edge detection on materials that confuse the sensor;
- understanding when the shift is tied to calibration or mechanics.
That full sequence is what I show on video, on a real machine, in Manual de Campo, in the same test order I use at the shop.
If you have already checked the file and the print keeps coming out clipped at the edge, stop testing on good media. Get into Manual de Campo, follow the diagnosis on video and get back to printing the full artwork, centered and in the right place, from the first foot to the last.
Quick answers about a Roland print cut off at the edge
Frequently Asked Questions
1. Why does my Roland cut off the edge of the image when the media is wider than the art?
Because it only prints inside the printable area it set when reading the media. A shifted origin point, a wrong edge reading or pinch rollers limiting the area make the usable width narrower than the art.
2. How do I know if the problem is the file or the machine?
Open the job in VersaWorks and check size, scaling and rotation. If the file is right, compare the printable width the machine shows with the width of the art.
3. Why does only one specific media come out shifted?
Clear, glossy, reflective or dark materials can confuse the edge sensor. The machine sets the area in the wrong place and the print lands shifted.
4. Why does the side only disappear at the end of the banner?
Usually the media is feeding skewed or drifting to one side as it advances. Check how it's loaded, how the roll sits on its holder and the pinch rollers.
5. When is it worth following Manual de Campo?
When you have already checked origin, file, VersaWorks and loading and the problem is still there. From there the diagnosis takes method, and that's what I show on video, on a real machine.
- 🎥 Straight-to-the-point video lessons on a real machine
- 🛠️ Organized troubleshooting for SP, VP, RS, VS, RE, RA and RF
- ⚡ Instant access as soon as payment is confirmed
- ♾️ Lifetime access to Manual de Campo and future updates