Master Print — Manual de Campo

Roland RS-640 vs RE-640: Real-World Differences, Who Each One Suits and What to Check Used

RS-640 or RE-640? Both are 64-inch eco-solvent printers that print only, but they come from different generations, and that changes ink, software and the used-market reality. I explain what actually sets them apart and how to choose without walking into a trap.

"Which is better, the RS or the RE?" That question lands in my messages almost every week, usually with two listing screenshots attached. The RS-640 tends to be cheaper, the RE-640 a bit more expensive, and the buyer is trying to figure out whether the price gap pays for itself or is just a number on a listing.

I work on both at the bench, and my answer is always the same: on the used market, the machine's condition decides more than the model. That said, there are real differences between them, and it's worth knowing them before you spend. Here I'll explain what changes in practice, with no made-up spec sheet, who each one makes the most sense for and what to check before paying. The full evaluation, on a real machine, is in the video lessons of Manual de Campo.

Does this sound like you?

  • You're comparing listings for a used RS-640 and a used RE-640.
  • You need a machine for banners and vinyl and already have a separate cutter.
  • You're not sure whether the RS-640's age affects maintenance.
  • You want to know if ink and software are the same on both.
  • You're afraid of buying a machine with a head near the end of its life.

What the two have in common

The RS-640 and RE-640 are 64-inch-class eco-solvent printers and, a point that trips up a lot of people, both print only; neither one cuts. If you need contour cutting on the same machine, neither solves that; that conversation is about the print and cut lines, like the VS, VP and SP.

They serve the same kind of work: banners, adhesive vinyl, vehicle graphics and wide pieces in general. The maintenance logic is similar too: head, cleaning station, ink supply, media feed and heaters.


Different generations: what that means in practice

The main difference is generation. The RS-640 is an older machine, and the RE-640 comes from a later Roland generation. In practice, that usually shows up in three places:

  • Ink: the compatible eco-solvent ink generation may not be the same. Confirm which ink the machine runs and never mix different types in the same system.
  • Software: the RIP and driver versions each one works best with can differ, and that affects setup on a new computer.
  • Parts and electronics: components aren't necessarily interchangeable between the two, even when they look the same.

Before buying ink or parts, or installing software, confirm the exact model. Assuming "it's all a 64-inch Roland" is an expensive mistake.


Production and quality: what to expect

The RE-640 was positioned as a production machine from a newer generation, while the RS-640 was, in its day, an entry option for wide-format printing. In practice, the speed and quality you get depend heavily on the print mode, the material, the media profile and, above all, the condition of the head.

An RS-640 with a healthy, well-calibrated head can deliver excellent work. An RE-640 with a tired head and a feed out of adjustment will deliver banding and gaps. That's why I don't recommend choosing based on the brochure alone: what prints is the machine in front of you.

It's also worth thinking about workflow. Since neither one cuts, contour-cut stickers mean moving the printed material to a separate cutter, with registration marks and an extra step. For a shop that lives on banners and print-only work, that's no big deal. For someone doing lots of contour-cut stickers, it might be the reason to look at a print and cut machine instead of either of these. When a customer asks me which to buy, the first thing I ask is what they print day to day.


Who each one makes the most sense for

  • RS-640: makes sense for someone starting out on a tight budget who's willing to deal with an older machine, as long as its condition is proven. It calls for more attention to preventive maintenance.
  • RE-640: makes sense for someone who needs steady production and prefers a newer-generation machine, usually with fewer years of use behind it.
  • Both: work best in shops that already have a separate cutter or that mostly do print-only work.

To see what tends to go wrong on each one, check RS-640 common problems and RE-640 common problems.


The used-market reality

Because it's older, the RS-640 is the one that shows up most often with high mileage: many years of banners, several owners and sometimes irregular maintenance. That doesn't rule it out, but it raises the odds of finding a worn cleaning station, a worn rail and a head near the end. Parts availability for older generations also varies.

The RE-640, being newer, tends to show up in better condition, but that's not a guarantee. The mini-case I see all the time: a buyer pays more for the RE-640 "because it's newer," and it arrives after months sitting idle, with gaps no cleaning will clear. Meanwhile, an RS-640 in daily use was running perfectly. Before deciding whether an older machine is worth investing in, read is it worth repairing an old Roland printer.


What to check before buying either one

If you're going to look inside the machine, it has to be turned off and unplugged. When handling ink or cleaning fluid, wear gloves and keep the room ventilated.

  • Nozzle check after the machine has been on for a while, not just right after a cleaning the seller ran.
  • A solid-fill print on banner or vinyl, to look for banding, gaps and feed issues.
  • Carriage noise and any error message during the job.
  • Drain bottle and cleaning station: signs of leaks or built-up gunk.
  • History: how long it sat, which ink it used and whether the head was ever replaced.

RS or RE, buying blind is the fastest way to turn savings into losses.

Really evaluating an RS-640 or RE-640, reading the nozzle check, separating the head from the cleaning station and keeping the machine producing is exactly what I show on video in Manual de Campo, on a real machine at the bench. Teach me to maintain my Roland →


Maintenance: what's the same and where Manual de Campo comes in

The basic routine is similar on both: print regularly, look after the cleaning station, keep the rail and encoder clean and control the environment. What changes are the details of parts, ink and software for each generation. When basic checks don't solve it, troubleshooting moves on to:

  • separating head failure from cap, wiper, pump and damper problems;
  • fixing feed and banding without wasting ink;
  • deciding whether the machine deserves the investment.

The complete step-by-step, in the order I use at the bench, is on video, on a real machine, in Manual de Campo.

RS-640 or RE-640, the one who knows how to maintain the machine is the one who profits from it. Join Manual de Campo today, learn to evaluate and care for your Roland and buy or maintain with confidence.


Quick answers about the RS-640 and RE-640

Frequently Asked Questions

1. Can the RS-640 or RE-640 cut?

No. Both print only. If you need to print and cut on the same machine, you are looking at the VS, VP or SP lines, or a separate cutter.

2. Do both use the same ink?

Not necessarily. They are from different generations, and compatible ink can vary. Confirm which ink your machine runs and never mix different types in the same system.

3. Is the RE-640 always better than the RS-640?

It is from a newer generation, but on the used market condition matters more. A well-kept RS-640 can be a better buy than an abused RE-640.

4. What matters most when buying a used RS-640?

Age and history. Check a nozzle print after the machine has been on for a while, a solid-fill print, the cleaning station and how long it sat idle.

5. Does Manual de Campo cover both?

Yes. The course shows on video, on a real machine, troubleshooting and maintenance that apply to the RS-640, the RE-640 and the other Roland models.

  • 🎥 RS-640 and RE-640 troubleshooting on video, on a real machine
  • 🛠️ A method for RS, RE, RF, RA, SP, VP and VS
  • ⚡ Instant access as soon as payment is confirmed
  • ♾️ Lifetime access to Manual de Campo and future updates
Learn to Maintain My Roland