Roland RS-640 Common Problems: What Goes Wrong and How to Approach Each One
Is your RS-640 banding, dropping nozzles, leaving wet prints, skewing media or throwing carriage errors? Here are the most common problems on this production printer, how to recognize each one and how far to go on your own.
A banner roll has been running since morning, the big order is almost done, and suddenly a band shows up every few inches. Or the panel flashes TEMPERATURE IS TOO LOW and the vinyl starts coming out wet, sticking on the take-up. Anyone who owns a Roland RS-640 knows that feeling of watching square feet turn into losses.
The RS-640 is a 64-inch eco-solvent printer that prints only and lives at production pace, and that pace is exactly why its faults show up the same way every time. On my bench, it's mostly banding, dropouts, drying and carriage complaints. Here I'll show you how to recognize each one, what to check safely and what's waiting on video in the Field Manual.
Does any of this sound familiar?
- Evenly spaced bands appearing halfway through the roll.
- Nozzles dropping out again a few hours after cleaning.
- Banners coming out wet or ink transferring to the back on the take-up.
- Media that starts straight and walks to one side after many yards.
- A new carriage noise, lost position or a MOTOR ERROR.
The RS-640 profile: a volume machine
Understanding how the RS-640 is used explains most of its faults. Typically it:
- runs wide, heavy rolls, often with a take-up unit;
- prints long jobs, where a tiny feed error becomes banding across yards of media;
- relies heavily on heaters and drying so prints don't smear on the roll;
- racks up lots of carriage hours, which takes its toll on the rail, encoder and cables.
What I see most in practice: a production RS-640 almost never fails out of nowhere. The fault grows, a faint band, a nozzle that drops now and then, a new noise in the carriage, until it becomes a stop in the middle of an order. Learn to read those first signs and a long downtime becomes a simple adjustment.
The most common Roland RS-640 problems
1. Banding
This is the most frequent RS-640 complaint. Regular bands across the job can come from media feed being off for that material, from dropping nozzles or from a print mode that's too fast for the application. I explain how to separate each cause in my article on Roland printer banding and horizontal lines.
2. Missing nozzles and weak color
Nozzles missing on the TEST PRINT, a color that looks washed out, or a whole channel failing. On a machine that runs this much, wipers and caps wear faster, and that shows up as dropouts that come back soon after cleaning.
3. Ink not drying or smearing on the roll
Banners and vinyl coming out wet, ink transferring to the back when it winds onto the take-up, or TEMPERATURE IS TOO LOW on the panel. That message is a temperature-related warning: the room and/or the heaters aren't yet where they need to be, and the exact cause depends on the situation. Ink that won't dry, on the other hand, usually combines heating, a cold room, media settings and print mode.
4. Media skewing on long jobs
The first yards are fine, but halfway through the roll the media starts walking to one side, wrinkling or touching the head. Pinch rollers, roll support and take-up tension are the first suspects. In worse cases you'll see a PINCH ROLL ERROR.
5. Carriage movement errors and MOTOR ERROR
A carriage that stops mid-pass, gets noisy, loses position or throws MOTOR ERROR. On an RS-640 with lots of carriage hours, think dirty rail, encoder residue, friction and tired cables. I've covered a code specific to this machine in Error 0110 on the Roland RS-640 and print carriage movement.
6. Ink system problems
Air in the line, a damper that no longer works properly or a poorly seated cartridge cause intermittent dropouts that look like clogs but don't respond to cleaning. If that's your pattern, read about the signs of a failing Roland ink damper. It's one of the places where the most ink gets wasted for nothing.
Symptoms that help you tell problems apart
- Bands with constant spacing: media feed or print mode.
- Bands that move around: unstable nozzles or air in the system.
- Dropouts back a few hours after cleaning: capping, wiper or ink line.
- Smears on the back of the roll: not enough drying for the speed or the media.
- Media drifting only after many yards: roll, take-up or pinch rollers.
- A new carriage noise: rail, friction or something rubbing; never ignore it.
A stopped RS-640 means square feet not leaving the shop and deadlines slipping.
Telling feed banding from nozzle dropouts, drying problems and carriage errors is exactly the diagnosis I show on video in the Field Manual, on a real machine, without replacing parts by guesswork. See the Field Manual →
Basic, safe checks
Any inspection near the carriage, cleaning station or rollers should be done with the machine powered off and unplugged. Nothing here requires taking anything apart:
- run a TEST PRINT before every large job and keep it as a reference;
- make sure the waste bottle isn't full and the tube isn't kinked;
- look for dried ink buildup on the wiper and caps;
- check that the roll is centered and well supported and the pinch rollers are at the marked positions;
- make sure the take-up is aligned and not over-tensioning the media;
- check the room temperature and that heaters are on for that media;
- clean the visible area around the rail of dust and lint, without lubricating anything on your own.
Important: the wrong lubricant on the rail or encoder can create a problem that didn't exist before. Cleaning and adjusting that area has its own procedure.
The RS-640 doesn't cut, and that changes the diagnosis
Because the RS-640 is print-only, any cutting problem lives outside it, usually on a separate cutter. That simplifies things: here the focus is head, ink, feed, drying and carriage mechanics. If you're comparing the RS-640 with a print and cut, remember that final cut quality depends on another machine and another workflow.
A case I see again and again: an RS-640 comes in "with banding" after several strong cleanings. The nozzle check was perfect; the bands were regular and only showed up on a new material. It was feed, not the head. A simple log of media in use, cleanings and error messages would have shown that on day one, without burning ink.
How far to go on your own, and where the Field Manual comes in
Nozzle checks, correct media loading, take-up setup and reading symptoms are within any operator's reach. Beyond that, the RS-640 demands method:
- a cleaning station maintenance routine suited to a high-volume machine;
- feed calibration per media, done the right way;
- how to deal with air in the line and dampers without wasting ink;
- diagnosing carriage and motor errors without touching what you shouldn't;
- when it makes sense to recover the head and when it's time to think about replacing it.
I stop the article here on purpose: these steps involve points that, done by trial and error, turn an adjustment issue into an expensive repair, and on a volume machine that means days without production. The full step-by-step lives in the Field Manual video lessons, on a real machine, with the right order and what not to do.
If your RS-640 is already banding, dropping nozzles or making noises, don't wait for it to stop in the middle of a big roll. Join the Field Manual, follow the protocol on video and get back to delivering on time.
Frequently asked questions about Roland RS-640 problems
Frequently Asked Questions
1. Does the Roland RS-640 cut?
No. The RS-640 is an eco-solvent printer without cutting. For contour-cut graphics it usually works alongside a separate vinyl cutter, with its own registration mark workflow.
2. Why does my RS-640 start banding after I change media?
Each material has a different thickness and behavior, and the feed that was right for one media may not suit another. That's the first thing to investigate before blaming the nozzles.
3. The ink doesn't dry and smears on the take-up. Is the heater broken?
It could be, but most of the time it's a combination of a cold room, media settings and print speed. Check that the heaters are active and the room isn't too cold before suspecting a fault.
4. My RS-640 carriage started making noise. Can I keep printing?
Ignoring a new noise isn't recommended. Power off, unplug and check that nothing is rubbing the carriage or rail. If the noise continues, it should be diagnosed with method before it turns into a motor error or a head strike.
5. Is it worth recovering the head on a heavily used RS-640?
It depends on the real condition of the nozzles after capping, wiper, ink and lines have been checked. That decision needs criteria, and it's one of the points I show on video in the Field Manual so you don't replace a head that could still be recovered.
- 🎥 Straight-to-the-point video lessons on a real machine
- 🛠️ RS-640 diagnosis in real production, no guesswork
- ⚡ Immediate access to content after confirmation
- ♾️ Lifetime access to the Field Manual and future updates