Roland RE-640 Common Problems: What Goes Wrong and How to Approach Each One
Is your RE-640 dropping nozzles after sitting idle, banding, leaving wet prints, skewing media or showing panel errors? Here are the most common problems on this 64-inch eco-solvent printer and how far to go on your own.
A banner order due tomorrow, the Roland RE-640 on since early morning, and the nozzle check comes out with gaps in two colors. One cleaning helps a little; the second one moves the gaps somewhere else. Or the print comes out wet and smears when you roll it up. If your RE-640 is doing that, you're not alone.
The RE-640 is the 64-inch eco-solvent printer many shops picked as their way into wide format. It prints only, often runs on an irregular schedule and pays for it, and that is by far the scenario I see most on my bench. Here I lay out its most common problems, how to recognize each one and what to check safely before the full procedure, which lives in the Field Manual.
Does any of this sound familiar?
- After a few idle days, the TEST PRINT is full of gaps.
- Every cleaning fixes one gap and creates another.
- Banding shows up right after you change media.
- Prints come out wet, smear as they roll up, or a temperature warning appears.
- A new carriage noise or a machine asking for SERVICE CALL.
Usage patterns explain most of the faults
In practice, I see the RE-640 suffer mainly for three reasons:
- irregular use: busy weeks followed by idle days, which is terrible for eco-solvent ink;
- lots of different media without specific settings for each one;
- cleaning station maintenance put off until the problem shows up on the print.
What the bench teaches: on an RE-640, faults almost always start small and give warning signs. Read them early and it's an adjustment; ignore them and it ends up being parts. The first thing I ask an owner is how many days the machine sat and which inks have been through it. If you're still choosing a machine, my Roland RE-640 vs RF-640 comparison covers the differences.
The most common Roland RE-640 problems
1. Missing nozzles after sitting idle
Monday morning, the machine powers up and the TEST PRINT is full of gaps. It's the classic case. Ink drying on the head face, a cap that doesn't seal well and a machine left unplugged for too long make the perfect combination. If yours sat for weeks, read my guide on a Roland printer sitting idle and how to restart it first, because restarting the wrong way can make it worse.
2. A nozzle check that changes with every cleaning
One gap disappears, another appears. That behavior means there's something beyond a clog: air in the line, a damper, capping or wiper. Knowing how to read the check is half the diagnosis, and I explain how in how to read a Roland nozzle check.
3. Banding
Regular bands across the job, especially after changing material. On the RE-640, one of the most common causes is a feed setting that was right for one media being used on another.
4. Ink not drying
Prints coming out wet, smearing as they roll up, or TEMPERATURE IS TOO LOW on the panel. That warning is temperature-related, the room and/or the heaters still below what's needed, and it doesn't point to a single cause. Poor drying, on the other hand, usually combines a cold room, heaters set below what the media needs and a print mode that lays down too much ink.
5. Skewed media and PINCH ROLL ERROR
Pinch rollers outside the correct positions, a poorly supported roll or media loaded at an angle make the media drift during the job. On long jobs, that turns into wrinkles and the risk of touching the head.
6. Carriage errors, MOTOR ERROR and SERVICE CALL
A noisy carriage, one that stops mid-pass, or a machine asking for a SERVICE CALL. Dirty rails, encoder residue, mechanical obstructions and tired cables belong here. It's the problem family where the most money is lost by tinkering without knowing.
Symptoms that help you tell problems apart
- Gaps only after idle time: ink drying and cap sealing.
- Gaps that move with every cleaning: air in the line, damper or wiper.
- Regular bands after a media change: feed for that material.
- Smears on the back of the roll: insufficient drying.
- Media drifting after a few yards: roll, pinch rollers or take-up.
- New carriage noise: stop and investigate before it becomes a motor error.
An RE-640 that's down or printing defects means late orders and ink going into the waste bottle.
Recovering nozzles after idle time, setting feed per media and diagnosing carriage errors in the right order is exactly what I show on video in the Field Manual, on a real machine. See the Field Manual →
Basic, safe checks
Any physical inspection near the carriage, cleaning station or rollers should be done with the machine powered off and unplugged. Nothing here requires taking anything apart:
- run a TEST PRINT and keep it as a reference to compare after each action;
- make sure the waste bottle isn't full and the tube is clear;
- look for visible dried ink on the wiper and caps;
- check cartridge expiry, origin and seating;
- load media straight with pinch rollers at the marked positions;
- check the room temperature and that heaters are active for that media;
- avoid leaving the machine without power for days if your model's manual recommends keeping it on standby.
Warning: don't run strong cleanings back-to-back "to see if it comes back". If two or three cleanings didn't change the check, stop and look for the cause. Insisting only wastes ink and fills the waste bottle.
RE-640 and ink: be careful with mid-life changes
Many RE-640s run on non-original ink at some point in their life. That's not forbidden, but it requires method: mixing inks without a proper changeover procedure is one of the causes of recurring dropouts and sediment in the system. Before concluding the head is finished, it's worth knowing which inks have been through the machine and how the change was done.
A classic case: an RE-640 that "lost its head" after two weeks sitting. On the bench, the head was fine; a dried-out cap wasn't sealing and the machine had been unplugged. Once the sealing was fixed and the recovery done in the right order, it printed again. A simple log of cleanings, wiper changes and ink changes would have shortened that diagnosis a lot.
How far to go on your own, and where the Field Manual comes in
Nozzle checks, correct loading, controlling the room and reading symptoms are within any operator's reach. Beyond that, the RE-640 demands method:
- the right cleaning station routine, without damaging caps and wipers;
- how to recover nozzles after idle time without stressing the head;
- feed calibration done in the right order, per media;
- how to deal with air in the line and dampers;
- diagnosing carriage and motor errors without touching what you shouldn't.
The article goes this far: what comes next involves the head and the carriage mechanics, and one step out of order turns a simple adjustment into an expensive repair. That's why the full step-by-step lives in the Field Manual video lessons, on a real machine, with the right sequence and what not to do.
If your RE-640 is already dropping nozzles, banding or complaining in the carriage, don't wait for it to stop completely with orders in the queue. Join the Field Manual, follow the protocol on video and get back to printing without pouring ink away.
Frequently asked questions about Roland RE-640 problems
Frequently Asked Questions
1. Does the Roland RE-640 cut?
No. The RE-640 is an eco-solvent printer without cutting. For contour-cut graphics it works alongside a separate vinyl cutter.
2. Why does my RE-640 drop nozzles every Monday?
Because eco-solvent ink dries when the machine sits idle, especially if it's unplugged or the caps don't seal well. A usage routine and cleaning station maintenance solve most of these cases.
3. Can I use third-party ink in the RE-640?
Many users do, but the changeover needs a proper procedure and ink from a reliable source. Mixing inks without method is one of the most common causes of recurring dropouts.
4. My RE-640 shows SERVICE CALL. Can I still fix it myself?
First power off, unplug and check that nothing is blocking the carriage or the media. If the message comes back after restarting, the diagnosis involves points that shouldn't be touched by trial and error.
5. Is it worth keeping an RE-640 today?
Yes, if the head and cleaning station are in good condition and the machine has a usage and maintenance routine. What kills an RE-640 is neglect and guesswork diagnosis, not the model itself.
- 🎥 Straight-to-the-point video lessons on a real machine
- 🛠️ RE-640 diagnosis on a real machine, no guesswork
- ⚡ Immediate access to content after confirmation
- ♾️ Lifetime access to the Field Manual and future updates