Master Print — Manual de Campo

Roland Nozzle Check: How to Read the Test Print and Decide Your Next Step

A nozzle check says far more than "there are gaps". I explain how to read your Roland TEST PRINT, what each type of failure usually means and what your next step should be.

You print the TEST PRINT, glance at that staircase of tiny lines for two seconds, spot "a few gaps" and hit a cleaning. Sometimes it works. Other times the next test shows gaps somewhere else, you clean again, and before you know it half a cartridge is in the waste bottle and nobody knows what was actually wrong.

When a Roland comes onto my bench, the nozzle check is the first thing I ask for, and it has almost never been read properly by the owner. That pattern tells you which channel, what kind of failure and what the next step is. Here I'll show you how to read it, and where reading it stops being simple.

Any of these ring a bell?

  • you can't tell if a gap is "normal" or a reason to clean;
  • crooked lines that won't go away with cleaning;
  • a whole color has vanished from the test;
  • every test shows the gaps in a different place;
  • the test looks fine, but the actual print has defects.

What the nozzle check (TEST PRINT) is on a Roland

On Roland eco-solvent printers (VP-540/540i, SP-300/540V, RS-640, VS-640/640i, RE-640), the nozzle check usually appears on the panel as TEST PRINT. The printer lays down a pattern of short stepped lines, organized by ink channel, where each tiny line represents one nozzle on the head.

If every nozzle is firing properly, the pattern is complete, even and aligned. Any failure shows up as a line that's missing, crooked, faint or doubled. It's a quick X-ray of print head health, and it's the foundation for almost every other decision: cleaning, feed calibration, bidirectional adjustment.

What I never do: never run a calibration with an incomplete nozzle check. Nozzles first, adjustments second.


How to print a test print you can trust

  • use clean, flat, white media, ideally the same media you print production on;
  • make sure the media is loaded properly with no waves in the test area;
  • let the ink dry a little before reading it, especially on glossy media;
  • read it in good light and, if you can, with a loupe;
  • keep the test with a date and a note (before/after cleaning) so you can compare.

A test printed on wavy or dirty media can show gaps that don't exist, or hide real ones.


Types of failure and what each one usually means

1. Isolated missing nozzles

One or a few lines missing, scattered around. The most common case: a light clog. A NORMAL cleaning usually takes care of it.

2. A whole block missing in one channel

A large run of nozzles without ink in one color. It can be a heavier clog, but also air in the line, a cartridge issue or poor ink supply to that channel. Look at the cartridge and the line before reaching for strong cleanings.

3. An entire channel gone

The color simply doesn't print. Before blaming the head, check the obvious: empty, badly seated or expired cartridge. If all that is fine, it points to air or a supply blockage, and cleaning alone rarely solves it.

4. Deflected nozzles (crooked lines)

The nozzle fires, but the drop leaves at an angle. Usually linked to dirt or residue on the nozzle plate near that nozzle. Sometimes a cleaning fixes it; sometimes a dirty wiper is the very thing causing it.

5. Faint or broken lines

The line exists but looks "dotted". A sign of an intermittent nozzle on the edge. It may recover with cleaning, or it may indicate wear.

6. Gaps in several channels at once

If failures show up in different colors in the same area, suspect what they all share: capping, wiper, cleaning pump. Repeated cleaning won't fix a cap that doesn't seal.

What I see most: owners treating a deflected nozzle like a clogged one and firing off POWERFUL cleanings. Deflection is usually dirt on the head face or a bad wiper, and a strong cleaning won't fix that. If yours really is a clog, the clogged Roland print head guide shows the safe path.

Misreading the nozzle check is the fastest way to burn ink and fix nothing.

This is exactly the reading I show on video, on a real machine: every type of TEST PRINT failure, what it points to and the right next step, with no impulse cleanings. Learn to diagnose it →


How to decide the next step after the test

  • Complete pattern: the head is fine. If the print still has issues, move on to feed calibration, bidirectional adjustment, media or profile.
  • A few isolated gaps: one NORMAL cleaning, new test, compare.
  • Gaps shrinking with each cleaning: it's recovering. Keep going calmly, step by step.
  • Gaps moving around but not shrinking: stop. The problem probably isn't just a clog (cap, wiper, air).
  • Whole channel missing: cartridge and supply first, cleaning second.
  • Same nozzles always dead, stable, with everything checked: possible head damage. A technical decision, not another try.

What burns the most ink: seeing any gap and jumping straight to POWERFUL cleaning. You burn a lot of ink, fill the waste bottle and learn nothing about the cause.

A bench case: a printer came in with magenta "fading out" for weeks. The tests the owner had kept showed the same block failing, always in the same channel, getting a little worse each time. That pointed to ink supply, not the head. The test history saved a head replacement nobody needed.


Quick checklist for reading a nozzle check

  • Clean, flat media? Test dry and in good light?
  • Which channel has the problem? One or several?
  • Is it missing, deflected or faint?
  • Are the gaps scattered or concentrated in a block?
  • Compared with the previous test: better, worse or just different?
  • Cartridges, waste bottle and room conditions checked?

Whenever you need to physically inspect the cap, wiper or cleaning station, power the printer off and unplug it, or use only the manual cleaning mode offered in your model's menu. Never force the carriage by hand.


The nozzle check as a routine, not just an emergency

Shops that print a nozzle check every morning before starting catch problems while they're still a tiny gap, not after a whole banner is ruined. Keeping the tests also builds a history: you can see whether one channel is slowly degrading, whether a cleaning really helped, or whether a nozzle keeps coming back.

That history is gold when deciding whether to keep trying to recover a head or accept that it's reaching the end of its life.


After the test: what you can decide yourself and what needs a diagnosis

Reading the test, cleaning step by step and checking cartridges and waste is safe and solves a lot. When the test shows gaps that don't respond to cleaning, the diagnosis moves to another level:

  • checking whether the cap seals and the pump pulls ink correctly;
  • spotting air in the line and where it's coming from;
  • cleaning the wiper and cap without damaging them;
  • deciding between recovering or replacing the head based on criteria, not hope.

Reading tests is learned by watching: in the Field Manual I show real test prints, failure by failure, and what to do in each situation, on a real machine, in the right order.

If your test shows failures that don't respond to cleaning, every blind attempt is wasted ink and risk to the head. In the Field Manual I read real test prints on video, failure by failure, on the machine, and show what to do in each case. Get in now and start reading a TEST PRINT the way a tech does.


What you gain by knowing how to read the test

  • you save ink by not cleaning when it isn't needed;
  • you separate head problems from feed or alignment problems;
  • you build a history for expensive decisions, like a head replacement;
  • you can talk to a technician on equal terms.

FAQ: reading the Roland nozzle check

Frequently Asked Questions

1. How often should I print a nozzle check?

Ideally at the start of every working day and always before important or long jobs. It takes little time and little media, and it keeps you from losing a whole job to a gap that was already there.

2. Do one or two missing nozzles ruin the print?

It depends on the print mode and the job. In modes with many passes, an isolated gap may not show at all. On solid fills and fast modes, it becomes a visible line. When in doubt, run a NORMAL cleaning and test again.

3. Why does the test show different gaps after every cleaning?

When gaps move around without decreasing, there's usually something beyond a clog: a cap that doesn't seal, air in the line or a dirty wiper. Cleaning more in that situation usually just increases ink consumption without fixing anything.

4. Can I run feed calibration with missing nozzles?

It's not recommended. Missing nozzles create lines that confuse the calibration reading, and you may end up adjusting the feed to compensate for a head problem. Get a complete nozzle check first, then calibrate.

5. How do I know if the print head is damaged?

When the same nozzles stay missing or deflected in a stable way, even after checking the cap, wiper, ink and line. Keeping dated tests helps a lot with that call, and it's one of the criteria I walk through on video in the Field Manual.

  • 🎥 Straight-to-the-point video lessons on a real machine
  • 🛠️ Focused on VP, SP, RS, VS, RE and RF with real cases
  • ⚡ Immediate access to content after confirmation
  • ♾️ Lifetime access to the Field Manual and future updates
Learn to Diagnose Now