Master Print — Manual de Campo

Roland RA-640 Water-Based Ink Care: Daily Routine, Media and Idle Time

Treating the RA-640 like a solvent Roland is the mistake I see most with this printer. I explain what changes in the routine of a water-based ink machine: drying, media choice, the room, cleaning, idle time and what you can safely check before you lose a head and a roll of media.

You got an RA-640, loaded the same banner you used on your old printer, and the ink pooled, ran and never dried. Or the print looked great, but after a week of sitting the nozzle check looked like it came from a different machine. And every video you find is about a model with a different ink.

On the bench, the mistake I see most with the RA-640 is treating it like a solvent Roland. It is a 64-inch, print-only machine that runs water-based ink, and that changes media, drying, cleaning and how you care for it when it sits. Here I explain what changes in the routine and what you can check without risk. The full procedure for your unit is on video in the course.

Sound familiar?

  • Ink will not dry, or pools on certain media.
  • Prints smear on the take-up or transfer to the back.
  • After a few idle days, the nozzle check comes back full of gaps.
  • On humid days drying gets much slower.
  • You are using products and routines meant for a different ink.

What changes with water-based ink

On a water-based ink printer, drying depends mainly on water evaporating and on the media's ability to accept that ink. That changes the logic of several things owners bring over from other machines.

The media becomes part of the system: it has to be made for this type of ink, with a coating that absorbs and holds the droplet. The wrong media is not just "worse"; it may simply not dry.

Before any routine, check your unit's documentation. The RA-640 configuration can vary by market and version, and the manufacturer lists the compatible ink, media and cleaning products for it. I cover the model's most common problems in Roland RA-640 common problems.


Media: the first thing to get right

The classic mistake from people coming off another machine is using the same banner or vinyl as always. In practice, this is what happens:

  • the ink beads up on the surface and does not hold;
  • the print stays wet, smears when touched and stains on the take-up;
  • colors lose definition because the droplet spreads;
  • results change a lot from one media batch to the next.

Use media meant for water-based ink and test before running a big job. Keep rolls wrapped and away from humidity: the coating that receives the ink is also sensitive to the environment.


Drying and the room: humidity matters more

With water-based ink, the humidity in the air directly affects drying time. On a muggy day, the same settings that worked yesterday can leave the print damp on the take-up.

The ink load of the print mode matters too: a lot of ink in a short time asks more of the media and of drying. If you see TEMPERATURE IS TOO LOW, treat it as a temperature-related warning: the room and/or the unit's heating, depending on the configuration, is still below what is needed, not a single specific cause.

A stable room, with no AC blowing straight at the printer and no sun on one side, helps a lot. I go into the room's effect in Roland printer room conditions.

An RA-640 treated like a different machine means a suffering head and wasted media.

The right routine for water-based ink, from media choice to cleaning and caring for the printer when it sits, is exactly what I show on video inside Manual de Campo, on a real machine. Show me the right RA-640 routine →


Cleaning: the right product for the right ink

This is one of the most serious risks. Cleaning fluid made for solvent ink is not interchangeable with fluid for water-based ink, and the reverse is also true. Using the wrong product in the cleaning station or near the head can damage seals, leave residue and hurt the nozzles.

  • use only the products specified for the ink installed in your unit;
  • do not mix inks from different systems or "use up" leftovers from another printer;
  • keep the wiper and capping clean, as the documentation describes;
  • do not run powerful cleanings back to back to cover a dropout that keeps returning: that burns ink and floods the station.

Safety: even without the strong smell of solvent inks, wear gloves, keep the room ventilated and shut the printer down properly before looking at the cleaning area.


Idle printer: the risk many people underestimate

Some people think water-based ink "does not dry out". It does. With the printer sitting, ink on the head surface dries, and if the capping seal is not good, the nozzles suffer fast.

  • avoid switching off the main power day to day, so the automatic routines can run;
  • print with some regularity, even if it is just a short test;
  • run a nozzle check before every important job and keep the photos;
  • if the printer will sit for a long period, plan for it before, not after.

The general logic of idle printers, and what to do before restarting, is in restarting a Roland that has been sitting idle.


A typical bench case

I have seen this story more than once: an RA-640 arrives at a company that only ever had solvent printers. The team applied the same routine as always: same cleaning fluid, same media, same habit of shutting everything off at night. Within weeks, nozzle dropouts that would not clear, damp prints and a cleaning station with strange residue.

On evaluation, the problem was not the printer itself. It was a routine designed for a different ink. Once the routine was adjusted for water-based ink, most of the symptoms went away, and what was left could be handled with a method.


How far to go alone, and where Manual de Campo comes in

Confirming your unit's documentation, using compatible media and products, looking after the room and never leaving the printer idle without a plan are all safe and prevent most problems. The next step involves:

  • understanding how the cleaning station works with water-based ink;
  • separating dropouts caused by drying from dropouts caused by sealing, air or dampers;
  • matching print mode and drying to your media and your room's climate;
  • building a daily and weekly routine specific to the RA-640.

A procedure for another model can be wrong for yours. That is why the complete step-by-step, built for the RA-640, is on video, on a real machine, inside Manual de Campo.

If your RA-640 is suffering under another printer's routine, change the method before you change parts. Join Manual de Campo today, learn how to care for a water-based ink printer the right way and keep your RA-640 producing without surprises.


Quick questions about the Roland RA-640

Frequently Asked Questions

1. Does the Roland RA-640 use the same ink as other Rolands?

No. The RA-640 runs water-based ink, which is why its media, drying and cleaning routine is different from solvent Roland printers. Always check your unit's documentation.

2. Can I use the same banner or vinyl from my other printer?

Usually not. Water-based ink needs media made for it, with a coating that receives and holds the ink. Incompatible media may not dry, may smear or may stain on the take-up.

3. Does water-based ink dry out in the head?

It does. With the printer idle and a compromised capping seal, nozzles can drop out quickly. Leaving the printer on for its automatic routines and printing regularly helps a lot.

4. Can I use cleaning fluid from another Roland on the RA-640?

It is not recommended. Use only the products specified for the ink installed in your unit. The wrong product can leave residue, damage seals and hurt the nozzles.

5. Does Manual de Campo cover the RA-640?

Yes. In the course I show on video, on a real machine, the diagnostic and maintenance logic that applies to the RA-640, respecting the differences of a water-based ink printer.

  • 🎥 Straight-to-the-point video lessons on a real machine
  • 🛠️ RA-640 specific routine plus SP, VP, RS, VS, RE and RF
  • ⚡ Instant access as soon as payment is confirmed
  • ♾️ Lifetime access to Manual de Campo and future updates
Take Care of My RA-640 Now