Master Print — Manual de Campo

VersaWorks Printing the Wrong Size: Scale, Artboard and Where the Measurement Gets Lost

Your file is the right size, but the print comes out bigger, smaller or out of proportion? I explain how to tell a file problem from a queue scale setting or a media feed issue, so you can find where the size changes before you reprint.

You pull the banner off the Roland, lay it out on the floor, run the tape measure across it, and your stomach drops. It's short. Or it's oversized. Or the width is dead on and the length is off. The storefront was measured twice and the file was built to the exact size, and now there's no way to "stretch" it on install day.

I see this a lot, and the owner has almost always blamed the printer before looking at the path the file takes to get there. Most of the time, the size got lost before any ink hit the media: in the artboard, in the image resolution or in a forgotten scale setting in the queue. Here I explain how to separate each cause when VersaWorks prints the wrong size. The complete diagnosis, on the real screen, is in the course video lessons.

Sound familiar?

  • The print comes out much smaller or much bigger than the file.
  • The width is right, but the length is a little long or short.
  • An image that looks "huge" on screen prints small on the banner.
  • Yesterday's job in the same queue came out right; today's didn't.
  • On print and cut jobs, the print is right but the cut doesn't follow.

First, measure how far off it is

Before you change anything, measure the print in both directions and compare it to the file. The type of difference already points the way:

  • Large, proportional error in both directions: almost always the file or the scale.
  • Small error, length only: usually media feed, not the file.
  • Error that changes from print to print: think media, temperature or roll tension.
  • Distorted image, stretched one way: proportions got unlocked somewhere along the way.

What I see most is an owner trying to fix a file error with a machine adjustment, or the other way around. Measuring first prevents that.


Artboard and export: where most errors start

The art can be the right size and still arrive wrong in VersaWorks. The first things I check:

  • A page or artboard that doesn't match the art: the job exports at page size, and the art comes along shifted or shrunk.
  • Export options like "fit to page" that resize without telling you.
  • Mixed units between the design program and whatever you check against later.
  • Files built at reduced scale, the way large storefronts often are, that someone forgot to compensate for at print time.

That last one is a classic: the designer builds the storefront at a fraction of full size to keep the file light, and the note that it needs to be scaled up gets lost between the office and production.


Raster images: resolution and physical size

With JPG, TIFF and other pixel-based images, the printed size depends on the combination of pixel count and the resolution stored in the file. The same image can mean a very different physical size if that information changes along the way.

  • a photo from the internet or a phone can arrive with a resolution that produces an unexpected size;
  • "increasing the resolution" carelessly changes the physical size too;
  • re-exporting from another program can store a different resolution than the original.

The classic mistake is enlarging the image in the design program until it "looks right" and sending a gigantic file to the RIP. The size may come out right, but processing grinds to a halt, as I explain in VersaWorks slow and queue stuck.


Scale and queue settings in VersaWorks

VersaWorks lets you adjust job size and scale, both on an individual job and in the queue settings. It's a useful tool, and that's exactly why it causes trouble:

  • a scale applied for a previous job stays saved and carries over to the next ones;
  • queue settings copied from another computer or another media bring adjustments nobody remembers;
  • fit-to-media-width style options resize the job automatically.

When a job that always printed right suddenly comes out the wrong size, the first thing I check is whether someone touched the queue. Very often the answer is a forgotten setting from another order.

A banner printed at the wrong size is media and ink in the trash, plus a customer waiting on a reprint.

Tracing the size from the file to the machine, checking artboard, resolution and scale in the right order and locking down the queue so it never happens again is exactly what I show on video in Manual de Campo, with the real VersaWorks screens and the Roland printing. See Manual de Campo →


Small differences: feed, media and heat

If the error is small and mostly in the length, the file is probably fine. That's when other factors come in:

  • Feed calibration that's off for that media, which I cover in Roland feed calibration;
  • Media that expands or shrinks with heater temperature and again as it cools;
  • Uneven roll tension or media feeding crooked.

Always measure after the piece has cooled and relaxed, not right as it comes off the machine. Banner and some vinyls change size with temperature, and measuring warm will fool you.


A typical case, and print and cut

A scenario I see again and again: a shop prints a run of signs and every one comes out slightly smaller than ordered. The operator had already been changing machine settings with no luck. The problem was in the queue: a scale used days earlier for a sample job was still active. Nobody had touched the Roland; only the setup was wrong.

On print and cut models such as the SP-300/540V, VP-300/540/540i and VS-300/540/640(i), there's a separate case: the print is the right size, but the cut doesn't follow it. That's no longer a file size issue, it's print-to-cut alignment, and it needs a different kind of diagnosis.


How far to go on your own, and where Manual de Campo comes in

Measuring both directions, checking the file's artboard and looking for a forgotten scale in the queue are things you can do now. What takes more method is:

  • tracing exactly where the size changes, from the design program to the print;
  • preparing raster images at the right size without choking the RIP;
  • organizing queues so a one-off adjustment doesn't contaminate later jobs;
  • reliably separating a file error from a media feed error.

That complete diagnosis is what I show on video, with the real screens, in Manual de Campo, so you get the size right on the first print, not the third.

Already had to reprint a banner because of the wrong size? Get into Manual de Campo today, follow the diagnosis on video and find where the size is getting lost before your next big job ends up in the trash.


Quick questions about wrong print size in VersaWorks

Frequently Asked Questions

1. Why does VersaWorks print smaller than my file?

The most common causes are an artboard that doesn't match the art, a scale applied in the queue or the job, a fit-to-media-width option, or image resolution changed on export. Measure the difference and check the file and queue first.

2. It's only a few millimeters off in length. Is it the file?

Probably not. A small error that only affects length is usually tied to media feed, the calibration for that material or expansion from heat. Measure after the piece has cooled.

3. Does image resolution change the printed size?

It can. With pixel-based images, physical size depends on pixel count and the resolution stored in the file. If that information changes on export, the printed size changes with it.

4. One job printed right and another in the same queue didn't. Why?

Often there's a scale or size adjustment applied to one specific job, or a queue setting that was changed recently. Compare the settings of both jobs before you touch the machine.

5. When is it worth following the Manual de Campo diagnosis?

When you've checked artboard, scale and resolution and the size is still off, or when the error changes from one print to the next. In the course I show the full sequence on video, on the real screen and the machine.

  • 🎥 Video lessons with the real screens and the printer running
  • 📏 File setup, scaling and media feed explained hands-on
  • ⚡ Instant access as soon as payment is confirmed
  • ♾️ Lifetime access to Manual de Campo and future updates
Get My Print Sizes Right