Master Print — Manual de Campo

Roland VS-640 and VS-640i Common Problems: Printing, Cutting and Head Strikes

Is your VS-640 or VS-640i getting head strikes, cutting off the print on long jobs, dropping nozzles or banding? Here are the most common problems on this 64-inch print and cut, how to recognize each one and how far to go on your own.

Six feet of wrap printed, the media cockles from the heat and you hear that scraping sound as the carriage passes. Or the contour cut, spot-on for the first pieces, starts drifting off the artwork at the end of the roll. On a Roland VS-640 or VS-640i, scares like that get expensive and rarely give you a warning.

As a 64-inch eco-solvent print and cut, the VS-640 carries the problems of a big printer and a cutter in one machine, and that's where many owners get lost. Head strikes and cut drift on long pieces are what I see on my bench most often. Here I sort the faults into families, show you what to check safely and what's on video in the Field Manual.

Does any of this sound familiar?

  • Smears or scratches always on the same side of the print.
  • A scraping sound when the media cockles from the heat.
  • Cuts that start on the art and drift off by the end of long pieces.
  • The machine can't read the marks and stops on CROP-MARK ERROR.
  • Nozzle dropouts that come back even after cleaning.

Why the VS-640 needs a different eye

On a VS-640, width and length matter. A small media drift that would go unnoticed on a smaller machine turns into:

  • shifted cuts at the end of a long job;
  • media edges lifting and touching the head;
  • banding that only shows up at certain lengths;
  • faster wear on pinch rollers, blade and cleaning station.

Know the platform: the logic behind these problems is shared with other Roland print and cut machines, and I explain the alignment side in cut and print alignment on the Roland VS-640 and VP-540.


The most common Roland VS-640 and VS-640i problems

1. Head strikes on long jobs

This is one of the most serious complaints, and owners talk about it a lot. After a few yards the media cockles, lifts at the edge or wrinkles from the heat and touches the head. The result ranges from smears and scratches on the print to real damage to the nozzle plate. Poor loading, a take-up pulling at an angle and a head height that doesn't suit the media are frequent suspects. If you hear the carriage scraping, read my article on Roland carriage noise and head strikes.

2. Cut drifting off the print, especially on long pieces

On a short sheet the cut is fine; on a two-meter piece it starts leaving the artwork. That usually involves media moving or shrinking during the process, crop mark reading and print-to-cut calibration.

3. CROP-MARK ERROR and unread marks

The machine can't find the marks, or finds one and gets lost on the next. A dirty sensor, very glossy or clear media, marks that are too small or printed too close to the edge are among the causes.

4. Missing nozzles and a channel that disappears

The TEST PRINT shows gaps, one color looks weak or is gone. It can be a clog, but on a VS-640 with hours on it, capping and wiper are usually part of the story, along with dampers and ink lines. See the signs of a failing Roland ink damper if dropouts come and go.

5. Banding

Regular stripes that follow the media feed, or irregular bands that move around. The first family points to feed and media settings; the second to unstable nozzles.

6. Weak cuts, perforating or scoring the liner

A worn blade, force and offset that don't suit the material, a blade holder with play, or cutting media that hasn't settled after heating.


Symptoms that help you tell problems apart

  • Smear or scratch on the same side of the media: edge lifting, possible head contact.
  • Cut right at the start and wrong at the end: media moving or shrinking.
  • Cut always shifted the same way: print-to-cut calibration.
  • Several colors failing at once: capping, pump or wiper.
  • Always the same channel failing: nozzles, damper or that color's line.
  • Cut failing only in one area of the bed: blade, cutting strip or media in that area.

One head strike on a VS-640 can cost more than months of proper maintenance.

Preventing head strikes, getting cuts right on long pieces and handling dropouts without wasting ink is exactly what I show on video in the Field Manual, on a real machine. See the Field Manual →


Basic, safe checks

For any physical inspection around the carriage, cleaning station, sensor or pinch rollers, power off and unplug the machine. Nothing here requires taking anything apart:

  • run a TEST PRINT and keep it as a reference;
  • load media straight, taut and with pinch rollers at the marked positions;
  • watch whether the media edge stays flat while printing, especially after heating;
  • make sure the take-up isn't pulling the media to one side;
  • check that registration marks are a suitable size and away from the edge;
  • run a small test cut before a big job;
  • check that the waste bottle isn't full.

What I tell every VS-640 owner: heard scraping, saw ink smears in the same spot or media lifting? Stop the job right away. Pushing on to "just finish this one" is how most VS-640 heads are lost.


VS-640 vs VS-640i: what changes in the diagnosis

Both share the same print and cut logic, and the problem families repeat. The practical differences are unit age, usage history, firmware version and RIP integration. That's why I always diagnose the actual machine, not the name on the cover.

A typical bench case: a VS-640 comes in with smears always on the same side and scratches across the print, and the owner is sure the head is failing. In reality, the media edge was lifting after heating and touching the nozzle plate on every pass. Stopping at the first scrape would have saved the head. Writing down the media and when the problem began closes that diagnosis much faster.


How far to go on your own, and where the Field Manual comes in

Loading media correctly, swapping blades, running nozzle checks and reading symptoms are things you can do yourself. From there on, the VS-640 demands method:

  • how to prevent head strikes on long jobs and tricky media;
  • the right order for feed and print-to-cut calibrations;
  • proper cleaning station maintenance without damaging the rubber parts;
  • how to handle dampers and air in the line without throwing ink away;
  • when a bad cut is an adjustment and when it's a part.

This far you can go safely: the rest involves the head, the most expensive part of the machine, and calibrations where the wrong order gets costly. That's why the full step-by-step lives in the Field Manual video lessons, recorded on a real machine, showing where to work and what not to do.

If your VS-640 is already scraping, smearing or cutting off the art, don't wait for the next head strike to act. Join the Field Manual, follow the diagnosis on video and protect the machine before the damage shows up.


Frequently asked questions about Roland VS-640 problems

Frequently Asked Questions

1. Why does my VS-640 only get head strikes after a few yards?

Because that's when the media has heated, cockled or started to drift. Loading, take-up tension, media type and head height are among the points to check. If you noticed contact, stop the job and inspect before continuing.

2. My VS-640 cuts fine on small pieces and wrong on big ones. Is it a fault?

Not always. On long pieces, small media movements or shrinkage add up. Before suspecting a fault, check loading, pinch rollers, registration marks and how long the media had to settle.

3. What's the practical difference between the VS-640 and VS-640i when it comes to problems?

The problem families are the same: head, cleaning station, feed and cutting. What changes is each unit's age, history and firmware and RIP details.

4. Does a head strike always ruin the head?

Not necessarily, but it can damage the nozzle plate or the edge of the head. After a strike, run a nozzle check and compare it with your previous one. If new, stable dropouts appeared, the diagnosis needs to be done carefully.

5. Can I adjust the VS-640 cut calibration myself?

It's possible, but order matters: before cut calibration, feed and loading must be right. Doing it out of order just moves the error somewhere else. I show that workflow on video, step by step, in the Field Manual.

  • 🎥 Straight-to-the-point video lessons on a real machine
  • 🛠️ VS-640/640i printing and cutting explained with real cases
  • ⚡ Immediate access to content after confirmation
  • ♾️ Lifetime access to the Field Manual and future updates
Get My VS-640 Back on Track