Roland Bidirectional Adjustment: Blurry Print, Double Image, Ghosting and Head Height
Blurry small text and doubled lines with a perfect nozzle check? I explain what bidirectional adjustment is on a Roland, why it drifts and when you should redo it.
The customer picked up the decal, held it close and asked why the lettering looked "shaky". You take a closer look: small text blurred, thin lines with a shadow next to them, edges that look printed twice. And the nozzle check is complete.
When a print like that lands on my bench, before I even think about the head I suspect the bidirectional adjustment, especially if head height or media changed recently. Here I'll explain what this adjustment is, why it drifts, how it ties to head height, and when the problem stops being an adjustment and becomes carriage mechanics.
Sound like your prints?
- small text looking shaky or out of focus;
- thin lines printing double or thicker than the file;
- a faint ghost next to edges and outlines;
- sharp in unidirectional mode, blurry in bidirectional;
- it started after changing head height or media.
What bidirectional adjustment is
On Roland printers (VP-540/540i, SP-300/540V, RS-640, VS-640/640i, RE-640), the carriage can print in both directions: going out and coming back. That doubles productivity, but creates a challenge. An ink drop doesn't fall straight down: it leaves the head while the carriage is moving, so it "flies" sideways a little before it hits the media.
On the way out, it shifts one way. On the way back, the other way. Bidirectional adjustment (often shown as BIDIR in the printer's adjustment menu) corrects the firing timing so drops from both directions land in exactly the same spot.
When that adjustment is off, each outbound and return pass places the image in a slightly different position, and you get that "doubled" image.
Symptoms of bidirectional misalignment
- blurry small text or text that looks "shaky";
- fine vertical lines doubled or thicker than in the file;
- ghosting: a faint shadow next to outlines and edges;
- overall lack of sharpness, even in high-quality modes;
- the problem disappears or improves a lot when you print unidirectionally.
Simple diagnostic test: print the same file in bidirectional and in unidirectional mode (when your VersaWorks print mode allows it). If unidirectional is sharp and bidirectional is blurry, bidirectional adjustment becomes the prime suspect.
Why bidirectional alignment drifts
1. Head height change
Many Roland printers have a head height lever for thicker media. The higher the head, the longer the drop flies and the bigger the offset. Changed the height? The bidirectional value that worked before no longer does.
2. Media change
Media of different thickness changes the distance between head and surface. A thick banner and a thin vinyl may need different values.
3. Print mode change
Carriage speed and resolution affect how the drop flies. A value that's perfect in one mode may not be perfect in another.
4. Deflected nozzles
Nozzles firing at an angle also create a double-image look, but then the nozzle check shows the deflection. That's why it's nozzle check first, bidirectional second.
5. Carriage mechanics
A carriage with play, a dirty rail or unstable position reading make the result vary, and no adjustment stays stable. That's already a maintenance scenario.
The classic owner mistake: raising the head height lever for a thicker banner, going back to thin vinyl and never redoing the adjustment. The printer doesn't "know" the distance changed. I've seen plenty of people ready to replace a head over this. Before any adjustment, confirm the nozzles first: the Roland nozzle check guide shows how.
Blurry prints drag down your quality and make customers doubt your shop.
This is exactly the diagnosis I show on video, on a real machine: confirming whether it is bidirectional, head height, a deflected nozzle or carriage play, and the right procedure for each case. Get sharp prints again →
Bidirectional, head height and media: how they connect
Think of it this way: head height + media thickness define how far the drop travels. Bidirectional adjustment compensates for that distance. If either one changes, the compensation needs to be reviewed.
- higher head = more protection against rubbing the media, but more sensitivity to bidirectional alignment;
- low head with wavy media = risk of a head strike, which can damage the nozzle plate;
- the right choice depends on the media, and bidirectional adjustment comes after that choice.
Careful: change head height only with the lever described in your model's manual, following the panel procedure. Never force parts or touch the carriage with the machine powered on.
A bench case: a printer came in after the adjustment had been redone several times, with every print coming out different. The value never settled. The cause wasn't in the menu: the carriage had play and the rail was dirty. When an adjustment won't stay put, the first thing I look at is the mechanics, not the number.
When to run bidirectional adjustment
- after changing head height;
- when you start using media of very different thickness;
- when blurry text or a double image shows up with a complete nozzle check;
- after maintenance on the head or carriage;
- when bidirectional mode looks visibly worse than unidirectional.
Checklist before adjusting
- Complete TEST PRINT, no deflected nozzles.
- Production media loaded, flat and well held.
- Head height set for that media.
- The print mode you'll actually use.
- After adjusting, print a file with small text and fine lines to confirm.
Double image: what you can check yourself and when it is bench work
Understanding the symptom, running the uni vs. bidirectional test and checking nozzles, media and head height is safe and already fixes many cases of blurry or double prints on a Roland. When the adjustment won't settle, or every print comes out different, the diagnosis goes deeper:
- reading the adjustment pattern correctly and criteria for choosing the value;
- fine adjustments that are often needed beyond the basic bidirectional setting;
- checking carriage play, rail and position reading;
- telling an adjustment problem apart from a head or mechanical problem.
This is learned by seeing the pattern on the machine: the full procedure, with pattern reading on a real machine, is in the Field Manual video lessons.
If the adjustment won't settle and sharpness comes and goes, every job delivered like that is a customer doubting your quality. In the Field Manual I show on video, on a real machine, how to read the adjustment pattern and how to tell when the problem is the carriage, the rail or the head. Get in now and deliver crisp small text again, in fast mode.
What you gain by understanding bidirectional adjustment
- small text and fine lines sharp again;
- you can use faster bidirectional mode without losing quality;
- you stop blaming the head for an adjustment problem;
- you know exactly when to redo the adjustment.
FAQ: bidirectional adjustment on Roland printers
Frequently Asked Questions
1. How do I know if a blurry print is bidirectional or the head?
Print the nozzle check first: if there are deflected nozzles, the problem starts at the head. If the test is complete, compare the same file in unidirectional and bidirectional mode. If only bidirectional is blurry, bidirectional adjustment is the main suspect.
2. Do I need to redo bidirectional adjustment after changing head height?
Yes. Head height changes how far the drop travels to the media, which changes the offset between outbound and return passes. After changing the height, redo the adjustment to keep prints sharp.
3. Does printing unidirectional all the time fix it?
It can work as a temporary fix or as a diagnostic test, but you lose speed. The goal is a well-adjusted bidirectional mode so you can produce with both quality and productivity.
4. What is ghosting in printing?
It's a faint shadow next to outlines, edges and text. Most of the time it's linked to misalignment between outbound and return passes, in other words, bidirectional adjustment. Deflected nozzles can cause something similar too.
5. I adjusted it and the result changes from day to day. Why?
When the adjustment won't stay stable, suspicion moves to the mechanics: carriage play, a dirty rail or unstable position reading. That diagnosis is more technical, and it's one of the topics I show on video in the Field Manual.
- 🎥 Straight-to-the-point video lessons on a real machine
- 🛠️ Focused on VP, SP, RS, VS, RE and RF with real cases
- ⚡ Immediate access to content after confirmation
- ♾️ Lifetime access to the Field Manual and future updates