Master Print — Manual de Campo

Roland Printing Garbage Characters or the Wrong File: Cable, Network, RIP or Printer?

Is your Roland spitting out random letters and symbols, printing the wrong file or dropping the job halfway through? From the service bench, I show you how to separate the computer, cable, network, RIP and printer before you blame the main board.

You sent a simple decal to the Roland, walked away for a minute, and came back to a full strip of random letters, numbers and symbols printed across the vinyl. Or worse: yesterday’s file came out instead, or the right job started and then the data just stopped coming, carriage parked and media wasted.

I get this call more often than you would think, and the pattern at the bench is almost always the same: the owner is already sure the board is fried, when the problem was somewhere between the computer and the printer. Here I explain how a Roland printing garbage characters happens on machines like the SP-540V, VP-540/540i, RS-640, VS-640i, RE-640 and RF-640, how to separate PC, cable, network, RIP and printer, and what you can safely check. The full electronics diagnosis lives in the course video lessons.

Sound familiar?

  • The printer outputs lines of text, codes or symbols instead of the image.
  • An old file, or part of another job, comes out.
  • The job starts fine and stops arriving halfway, with no error on the panel.
  • It only happens with big files or after the PC has been on for hours.
  • It started after a new computer, cable, router or Windows update.

What is really going on when garbage characters print

A printer does not make up letters. When it prints gibberish, it is almost always receiving data it cannot interpret: a file that arrived corrupted, incomplete, in the wrong format or sent down a path that skipped the RIP. It tries to read that as print commands and turns the junk into ink on your media.

The same logic applies to the wrong file and to the job that dies halfway. In the first case, a queue or buffer held on to an old job. In the second, the data stream was cut off: the computer went to sleep, the cable lost contact, the network dropped for a few seconds or the software froze while sending.

That is why I always say garbage output is a communication symptom, not a board diagnosis. It can be the board, sure, but that is the last suspect in line, not the first.


PC, RIP or printer: the first split

Before you touch anything, ask one question: does the problem follow the computer or the printer? Here is how I sort it out in practice:

  • It happens with any file, even a simple test: look at the cable, port and output settings first.
  • It only happens with heavy files: think overloaded RIP, a full drive, PC memory or a transfer being cut off.
  • It happens after hours of uptime: power saving on the PC or USB port is a strong suspect.
  • It started after a change (new PC, router, update): the problem is almost always in that change.
  • The printer’s own internal tests print fine, like the nozzle check: the print side is alive and the focus is communication.

USB cable, network and port: where most cases start

In the shop, what I see most is physical and cheap. A USB cable that is way too long, joined with an extension, running next to power cords or plugged into a hub with the mouse, keyboard and a thumb drive. On a network, an IP address that keeps changing, a consumer router rebooting itself or a crushed Ethernet cable behind the desk.

  • use a good-quality cable, as short as practical, plugged straight into the computer, no hub, no extension;
  • keep the data cable away from power cords, motors and lighting ballasts;
  • switch ports on the PC and, if you can, test another cable before drawing conclusions;
  • on a network, make sure the printer always keeps the same address and the cable and switch are solid;
  • turn off PC sleep and USB power saving during production.

Every strip of gibberish is wasted media, wasted ink and an hour of machine time gone.

Methodically separating cable, network, RIP and printer electronics, without swapping parts on a hunch, is exactly the diagnosis I show on video inside Manual de Campo, on a real machine. Stop wasting media on this →

The classic owner mistake is replacing the cable with a longer one to reach another desk, and suddenly getting intermittent faults that were never there before. Cable length and quality matter more than most people think.


Driver, queue and output settings in VersaWorks

Roland eco-solvent printers are built to receive jobs processed by the RIP. When someone prints straight from a design program through a generic Windows driver, or the printer ended up installed twice on different ports, the result can be exactly this: nonsense text on the media.

  • make sure the job goes out through the RIP to the right printer, not to a “ghost” Windows printer;
  • check for two installs of the same machine pointing to different ports;
  • clear the queue before testing again so you do not resend an old stuck job;
  • test with a small, simple, freshly processed file, not the problem file;
  • if the PC is sluggish or the drive is full, the transfer can get cut halfway.

If the RIP cannot see the printer at all, that is a different road, and I cover it in VersaWorks printer not found.


When the problem is inside the printer

Once you have swapped the cable, port, computer and test file and the garbage keeps showing up, then the suspicion moves to the printer. The families I consider are a communication connector with poor contact or corrosion, a faulty interface board and failures that show up after a power surge.

Before any inspection, power off from the panel, turn off the main switch and unplug the power cord. Do not open electronics covers or disconnect boards unless you know exactly what you are doing. If there was a storm, a hard power outage or a burning smell, have a qualified electrician check the electrical installation before you power up again.

Keep in mind: if the printer stops mid-job with an error on the panel, that is usually a different story, tied to mechanics, media or temperature. I break that scenario down in Roland stops printing mid-job.


A case I keep seeing at the bench

A print shop moves the printer to free up space. To reach the computer, they buy a much longer cable and run it alongside the power strip feeding the vinyl cutter. From then on, every so often a band of symbols comes out, other times the job stops halfway. The owner replaces the computer, reinstalls the RIP and is already pricing a board.

When the printer arrives, the internal tests print perfectly. The fault was in the data path all along. What got expensive was the time spent replacing things that did not need replacing.


How far to go on your own, and where Manual de Campo comes in

Everything above is safe and already solves a good share of cases: cable, port, network, queue, duplicate driver and power saving. When it does not, the diagnosis starts to require:

  • confirming methodically whether the fault is in the communication or in the printer’s electronics;
  • checking internal connectors and cables without creating a new fault;
  • understanding how each model receives and processes the data sent by the RIP;
  • deciding with real criteria between an adjustment, a contact cleaning or a board replacement.

You do not diagnose a communication board by guessing. People who swap parts on suspicion usually pay twice. That is why the full path, from the computer to the electronics, is something I show on video, on a real machine, inside Manual de Campo, along with a Roland eco-solvent maintenance checklist that prevents a lot of downtime.

If you already swapped the cable and port and your Roland is still printing junk, stop testing in the dark. Get into Manual de Campo today, follow the video diagnosis from the simplest step to the most technical, and find out where communication is breaking before you pay for a board you may not even need.


Quick answers about a Roland printing garbage characters

Frequently Asked Questions

1. Does a Roland printing garbage characters mean the board is bad?

Not necessarily. In most cases the printer is receiving corrupted data or data sent down the wrong path. The cable, port, network, a duplicate driver and a stuck queue all come before any board suspicion.

2. Why did my Roland print an old file?

Usually because a previous job got stuck in the computer or RIP queue and was released later. Clear the queue before resending and test with a small, freshly processed file.

3. Can a long USB cable cause this?

Yes. A cable that is too long, low quality, extended or running next to power cords is a common cause of intermittent communication faults. Use a short cable plugged straight into the computer.

4. Can I print straight from CorelDRAW or Illustrator without the RIP?

That is not the intended path for these printers. Sending through a generic driver can produce exactly the gibberish symptom. Jobs should be processed and sent through the RIP to the correct printer.

5. When should I follow the Manual de Campo protocol?

When you have already swapped the cable and port, tried another computer or a simple file, and the problem is still there. From that point the diagnosis involves the printer’s electronics, and I show that sequence on video, on a real machine, in Manual de Campo.

  • 🎥 Video troubleshooting from the PC to the printer
  • 🔌 Cables, network, RIP and boards explained hands-on
  • ⚡ Instant access as soon as payment is confirmed
  • ♾️ Lifetime access to Manual de Campo and future updates
Fix My Roland’s Communication