Master Print — Manual de Campo

Ink Leaking Inside Your Roland: Puddle Under the Carriage, Cartridge or Ink Line?

Found a puddle of ink under the carriage, at the bottom of the machine or around the cartridges? I explain where internal leaks on a Roland usually come from, why they threaten the electronics and what you can safely check before it gets worse.

You open the cover to free a jammed banner and there it is: an ink stain on the bottom of the machine, under the carriage, running toward a corner you can barely reach. Or the cartridge area is sticky, with drips that come back even after you wipe them. The machine is still printing, but one question won't go away: where is this ink coming from, and what is it reaching?

Internal leaks are one of the problems I most want to catch early, because ink in the wrong place doesn't sit still: it runs toward cables, sensors and boards. I've had machines come in with an electronic error whose real origin was a drip nobody took seriously for weeks. In this article I explain where ink leaking inside a Roland comes from on models like the SP-540V, VP-540/540i, VS-540/640(i), RS-640, RE-640 and RF-640, and also on the RA-640, which uses water-based ink. The repair for each point is in the Manual de Campo video lessons.

Sound familiar?

  • A puddle or stain of ink under the carriage, at the parking area.
  • The cartridge area is sticky, with ink running downward.
  • Ink lines with drops on them or fittings that are always wet.
  • Drips on your prints along with mess inside the machine.
  • One color running out much faster than the others for no clear reason.

Why an internal leak is urgent

Ink outside its path does three kinds of damage. First, it fouls and damages reading parts such as the encoder strip and sensors, causing errors that look like motor or board faults. Second, it reaches cables and connectors, creating bad contacts or shorts. Third, it can get onto circuit boards, and then the repair stops being cheap.

On top of that, the solvents in many inks attack some plastics and rubber over time. And no ink of any type gets along with electronics: liquid near a board is always a risk. Either way, a leak is not something to leave for the next service.


Where the ink usually comes from

  • Dampers: a damper with a tired seal or poor fit is one of the top leak sources on the carriage.
  • Ink line fittings: a dried-out, cracked or loose tube at a joint.
  • Cartridge area: a cartridge not seated properly, refilled in a makeshift way or with a damaged seal.
  • Cleaning station: caps, drain tube or bottle out of place, overflowing inside the machine.
  • Head flooding: excess ink running off the nozzle plate, sometimes tied to pressure or sealing.

If the leak is clearly at the damper, I cover the replacement signs in Roland ink damper replacement signs.


How to read the clue the puddle leaves

Where the stain is and what color it is tell you a lot. A single color points to that color's line, damper or cartridge. All colors mixed under the carriage parking area usually come from the cleaning station or the drain. Ink running top to bottom near the cartridges suggests a fitting or cartridge. A stain that follows the carriage path makes me think of a damper or the head dripping while it moves.

When a machine like this lands on my bench, the first thing I do is photograph and note where the ink is before cleaning anything. Cleaning everything before looking erases the evidence.

An ignored leak turns into an electronic error, a damaged board and a stopped machine.

Finding exactly where the ink comes from, separating damper, line, cartridge and cleaning station, and fixing it without creating a new leak is exactly what I show on video in Manual de Campo, on a real machine. Show me how to find my leak →


What you can safely do right now

First, shut down from the panel, turn off the main switch and unplug the power cord. With ink near electronics, this is not the time to test with it powered. Then:

  • wear gloves and keep the room ventilated, especially with eco-solvent ink;
  • blot the puddle with lint-free paper or cloth, without spreading it sideways;
  • check visually that cartridges are seated and that no visible tube is loose;
  • make sure the drain bottle is in place and not full;
  • don't take apart dampers, lines or the carriage unless you know exactly how it goes back.

If ink has reached boards or cables, or there's a burning smell, don't power back on before it's evaluated. And if the source seems to be the drain, read about a full Roland drain bottle.


Mistakes that turn a drip into a big bill

  • keeping the machine printing "just until this job is done" with ink running;
  • spraying solvent over the dirty area and washing ink toward cables and sensors;
  • overtightening plastic fittings and cracking them;
  • replacing the damper without finding out why the old one leaked;
  • using makeshift refills or cartridges that don't seal properly.

The classic owner mistake is treating the leak as a mess: wipe it, the machine looks fine, and a few days later the stain is back and bigger.


Why leaks tend to come back

A leak is rarely just "a bad part". There's usually a reason behind it: a damper that worked under the wrong pressure, a tube that dried out from heat, a cartridge refilled in a way that left air or dirt on the seal, a cleaning station that won't drain because the waste tube is kinked or clogged. If you replace only the part that dripped and leave the cause alone, the problem moves to the new part.

What I see most often is two things adding up: a component that was already tired and a habit that stresses the system, like back-to-back powerful cleanings or makeshift refills. Fixing it for good means understanding the why, not just the where.


A typical case

A shop notices drips of a single color on prints and, under the carriage, a stain of the same color. They wipe it, keep printing, and weeks later carriage position errors start showing up. Suspicion turns to the motor and the board.

On the bench, that color's damper was leaking and the ink had run all the way to the encoder strip. Caught early, it was a damper. Ignored, it became a delicate encoder cleaning and a scare with the electronics.


How far to go on your own, and where Manual de Campo comes in

Powering down, containing the ink and checking cartridges, drain and visible lines is safe and keeps the damage from growing. Beyond that, the job requires:

  • pinpointing the exact source of the leak without taking apart what doesn't need it;
  • evaluating dampers, lines, fittings and the cleaning station properly;
  • cleaning the encoder, sensors and affected areas without causing new damage;
  • understanding what caused the leak so it doesn't come back.

I show all of that on video, on a real machine, in Manual de Campo, in the order I use on the bench.

If you found ink where it shouldn't be and it keeps coming back, don't wait for it to reach a board. Join Manual de Campo today, follow the diagnosis on video and fix the leak while it's still a cheap problem.


Quick answers about ink leaking inside a Roland

Frequently Asked Questions

1. Can I keep printing with ink leaking inside my Roland?

It isn't recommended. Running ink can reach the encoder, sensors, cables and boards. The safest move is to power down, unplug, contain the ink and find the source before going back to production.

2. Where does the ink puddle under the carriage come from?

The most common sources are a damper with a tired seal, a loose or dried ink line fitting, an overflowing cleaning station and a flooding head. The color and position of the stain help separate them.

3. Can an ink leak damage the main board?

It can. Ink that reaches cables, connectors or boards can cause bad contacts, shorts and electronic errors. That's why an internal leak should be treated as urgent.

4. Should I clean the leaked ink with solvent?

Carefully. Spraying solvent over the area can spread ink toward cables and sensors. Wear gloves, ventilate, blot first and never wet the electronics. I show the complete method in the course.

5. When should I follow the Manual de Campo diagnosis?

When the stain comes back after cleaning, the source isn't visible, or ink has already reached the encoder, sensors or cables. I walk through that diagnosis and repair sequence on video, on a real machine.

  • 🎥 Ink leak troubleshooting on video, on a real machine
  • 🛠️ Dampers, ink lines, cartridges and capping explained in practice
  • ⚡ Instant access as soon as payment is confirmed
  • ♾️ Lifetime access to Manual de Campo and future updates
Find the Source of the Leak