Master Print — Manual de Campo

Roland Ink Drops on Print: Why Blobs and Smudges Fall on Your Media

A round blob in the middle of the photo, a dragged smudge, a mark always on the same side? Drawing on years at the bench, I explain where that ink builds up on your Roland, how to read the shape of the mark and what you can safely check before you waste more media.

Nozzle check: perfect. Print: ruined. Somewhere in the middle of a ten-foot banner a fat ink drop lands right on the customer's face, and two passes later there is a dragged smudge next to it. You run a cleaning, reprint, and another drop shows up. That is media, ink and machine time going straight into the trash.

Ink drops are one of the most common complaints that land on my bench, and they are almost never bad luck or a dead head. It is ink building up somewhere a nozzle check can't show you. Here I explain where it comes from on Roland eco-solvent printers (SP, VP, RS, VS, RE and RF lines), how to read the mark, and what you can safely check. The full cleaning routine, in the right order, is what I show on video in the course.

Sound familiar?

  • A round drop lands in a random spot on the print.
  • Smudges dragged in the direction the carriage moves.
  • The mark always shows up on the same side of the media.
  • Drops right after you ran a cleaning.
  • A perfect nozzle check, but the job still comes out stained.

Drop, blob or smudge: what each symptom is telling you

Before you start wiping everything, take a careful look at the print. The shape of the mark already tells you a lot:

  • round, sharp-edged drop: usually ink that built up somewhere on the carriage or head face and fell off in one piece;
  • dragged smudge along the carriage direction: something touched the wet print, either debris hanging from the head or the media itself lifting up;
  • marks always on the same side of the print: often points to the side where the carriage parks, cleans or reverses;
  • drops right after a cleaning: excess ink on the head face or a wiper that is not removing what it should.

What I ask every customer to do: take a photo of the defect and note where on the media it appeared, whether at the start of the job, after a cleaning or after a long run. That record saves you hours of trial and error.


The most common causes of ink drops on a Roland

1. Dirty head face or ink buildup

Over time the head face (the plate that holds the nozzles) collects a film of ink, dust and lint. As that buildup grows it forms a droplet that eventually falls onto the media. It often comes together with missing nozzles, so it is worth reading the guide on a clogged Roland print head and missing nozzles as well.

2. Dirty, worn or misaligned wiper

The wiper is the blade that sweeps excess ink off the head face. When it is caked with dried ink, deformed or worn at the edge, it stops cleaning and starts smearing, leaving a hanging drop that falls on the next pass. I cover this in the article on Roland wiper and capping station cleaning.

3. Ink mist building up under the carriage

While printing, part of the ink turns into a fine mist that never reaches the media. That mist settles on the underside of the carriage and the sides of the head. After weeks without cleaning it forms drops that shake loose with carriage vibration. This one is easy to miss because it never shows up on a nozzle check.

4. Condensation and room conditions

A shop with big swings in temperature and humidity, a printer next to an open door, an AC vent blowing straight at it, or media heaters running hotter than needed can all promote moisture and solvent buildup on cooler parts of the carriage and cover. That moisture mixes with ink mist and drips.

5. Head height too low for the media

When the head runs too close to the media, any wave or lifted edge touches the head face, contaminates the nozzles and then returns that ink as a smudge. Most Roland models let you change the head height, and choosing the right height for each material is part of a proper setup.


Why running another cleaning will not fix it

Almost everyone reaches for the cleaning menu first. But the automatic cleaning takes care of the nozzles, not the buildup on the sides of the head, under the carriage or on the wiper. Worse, each cleaning pushes more ink into that area, and if the wiper is bad you increase the chance of a drop on the next job.

The classic case I get in the shop: the owner has already run cleaning after cleaning, the nozzle check is spotless and the drops keep coming. When I open the cover, the head is fine, but the underside of the carriage and the sides of the head are loaded with ink. If the problem is drops and smudges rather than missing nozzles, the fix involves a correct manual cleaning and understanding what is causing the buildup. Back-to-back automatic cleanings only burn ink and fill the waste bottle.

Every drop in the middle of a job is media, ink and machine time thrown away, with the customer waiting.

Finding where the drop comes from and cleaning the head face, wiper and carriage underside without scratching the nozzle plate is exactly what I show on video in the Field Manual, on a real machine, the way I do it at the bench. Stop losing media to ink drops →


Basic, safe checks you can do today

None of these checks require opening the machine or touching the head. Any inspection around the carriage should be done through your Roland's maintenance menu, which moves the carriage to the access position, or with the printer switched off. Never push the carriage by hand.

  • Note when the drops appear: start of the job, after a cleaning, or only after long runs.
  • Use a flashlight to look at the front cover and carriage area for visible ink buildup, lint or hanging drops.
  • Check that the media lies flat on the platen and the edges are not lifting.
  • Make sure the head height makes sense for the thickness of the material you are running.
  • Look for drafts, direct sunlight or big temperature swings near the printer.
  • Print a nozzle check to separate drops (buildup) from missing nozzles (clogging).

Quick read: drops with a perfect nozzle check are almost always buildup outside the nozzles. Drops with a failing nozzle check mean the head face itself is compromised and needs more careful attention.


The mistake that turns a drop into an expensive repair

The biggest risk here is cleaning the head face with the wrong material, too much pressure or the head in the wrong position. The nozzle plate is extremely delicate: one scratch or a strand of lint left behind can kill nozzles permanently. I also get plenty of machines on the bench after someone used the wrong solvent and attack the capping and wiper rubber, creating a brand-new problem.

Heads up: if the media is waving and touching the head, cleaning only buys you a few hours. The cause is still there. If you already hear the carriage rubbing, also read the article on Roland carriage noise and head strikes.


How far to go on your own, and where the Field Manual comes in

The checks above help you figure out whether the drops come from buildup, room conditions or media touching the head. The next step involves procedures you really need to see being done:

  • correct manual cleaning of the head face and sides, with the right materials and order;
  • cleaning the underside of the carriage where ink mist collects;
  • judging and replacing the wiper at the right time;
  • choosing the head height and media settings for each material.

From here on, text is not enough: you need to watch the hands, the right materials and the right order. That step-by-step, including what not to do, is in the Manual de Campo (Field Manual) video lessons, recorded on a real machine. If your Roland keeps dropping ink and you have already thrown media away because of it, join the Field Manual today and fix it with a method, before a drop turns into a scratched head and a much bigger repair bill.


Frequently asked questions about ink drops on Roland printers

Frequently Asked Questions

1. Why does my Roland drop ink only on some jobs?

Because ink buildup needs time and vibration to break loose. Long jobs, heavy coverage and jobs printed right after a cleaning are more likely to show a drop. Writing down when it happens helps you find the source.

2. Does an ink drop mean my print head is damaged?

Most of the time, no. Drops usually come from buildup on the head face, the wiper or under the carriage. If the nozzle check looks good, the head is probably healthy and the issue is cleaning or media touching the head.

3. Can I clean the head face with any cotton swab?

It is not recommended. Lint and abrasive materials can scratch the nozzle plate or leave residue that makes things worse. Use only materials made for eco-solvent ink and follow the correct procedure, which I show on video in the Field Manual.

4. Does head height affect ink drops?

Yes. With the head set too low, any wave in the media touches the nozzles, dirties the head face and gives that ink back as a smudge. Setting the height to match the material greatly reduces that risk.

5. How often should I clean around the print head?

It depends on your print volume and environment. If you print every day you need a fixed routine to inspect the wiper, capping and carriage area. A good routine prevents most drops and protects the head in the long run.

  • 🎥 Straight-to-the-point video lessons on a real machine
  • 🧽 Head, wiper and capping cleaning shown step by step
  • ⚡ Immediate access to content after confirmation
  • ♾️ Lifetime access to the Field Manual and future updates
Stop the Ink Drops on My Roland